manualshive.com logo in svg

Agilent Technologies 66319B, Руководство пользователя

Поделиться
Скачать
Agilent Technologies 66319B Скачать руководство пользователя страница 18

2 - General Information 

 

18 

‰

 

Triggered acquisition of digitized current and voltage waveforms 

‰

 

External measurement trigger input on units with firmware revision A.03.01 and up 

♦

  Open sense lead protection on output 1. 

♦

  Automatic overvoltage protection tracking. 

♦

  Over-temperature, RI/DFI protection features, programmable voltage limit and current limit. 

♦

  Non-volatile state storage and recall with SCPI command language. 

♦

 User-configurable 

power-on/reset settings (see Appendix B). 

Table 2-3. Agilent Model Differences 

Item  

66321B 

 66321D 

 66319B 

66319D 

66311B/D

1

  

66309B/D

1

 

0 - 1 A range current 
measurements (output 1) 

YES YES YES YES 

NO 

NO 

0 - 20 mA range current 
measurements (output 1) 

YES YES YES YES 

YES 

YES 

4-mode output compensation 
(output 1) 

YES YES YES YES  2 

modes  2 

modes 

Auxiliary output (output2) 

NO 

NO 

YES 

YES 

NO 

YES 

External DVM input 

NO 

YES 

NO 

YES 

66311D only 

66309D only 

Output resistance 
programming (output 1) 

YES YES YES YES 

NO 

NO 

Automatic overvoltage 
tracking (output 1) 

YES YES YES YES 

NO 

NO 

Compatibility 

commands  NO NO NO NO 

YES 

NO 

External measurement trigger 
input

2

 

YES YES YES YES 

NO 

NO 

1

Earlier models not covered in this manual (order manual p/n 5964-8125) 

2

Available only on units with firmware revision A.03.01 and up 

Front Panel Controls 

The front panel has both rotary and keypad controls for setting the output voltage and current. The panel 
display provides digital readouts of a number of output measurements. Annunciators display the operating 
status of the dc source. System keys let you perform system functions such as setting the GPIB address 
and recalling operating states.  Front panel Function keys access the dc source function menus. Front 
panel Entry keys let you select and enter parameter values. Refer to chapter 5 for a complete description 
of the front panel controls. 

Remote Programming 

NOTE:

 

The dc sources described in this manual can only be programmed using the SCPI 
programming language. 

The dc source may be remotely programmed via the GPIB bus. GPIB programming is with SCPI 
commands (Standard Commands for Programmable Instruments), which make dc source programs 
compatible with those of other GPIB instruments. Dc source status registers allow remote monitoring of a 
wide variety of dc source operating conditions. Refer to chapters 6 and 7 for more information. Chapter 8 
is a language dictionary of all SCPI commands that can be used to program the dc source. 

Содержание 66319B





















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды