Agilent Technologies 66319B Скачать руководство пользователя страница 44

Страница: 44 / 180

5 – Front Panel Operation

Display

14-character vacuum fluorescent display for showing output measurements and
programmed values.

Annunciators

Annunciators light to indicate operating modes and status conditions:

The dc source output is in constant-voltage mode.

The dc source output is in constant-current mode.

Unr

The dc source output is in an unregulated state.

Dis

The dc source output is disabled (off).

OCP

The overcurrent protection state is enabled.

Prot

One of the dc source's output protection features is activated.

Cal

The dc source is in calibration mode.

Shift

The Shift key is pressed to access an alternate key function.

Rmt

The GPIB interface is in a remote state.

Addr

The interface is addressed to talk or to listen.

Err

There is a message in the SCPI error queue.

SRQ

The interface is requesting service from the controller.

Rotary Control

The rotary control lets you set the output voltage or current as well as menu
parameters. Press

and

to select the resolution, then adjust the value with

the knob.

Line

This turns the dc source on or off.

System Keys

The system keys let you:

Return to Local mode (front panel control)

Set the dc source GPIB address

Selects the remote programming interface

Select the output channel on units with more than one output

Display SCPI error codes and clear the error queue

Save and recall up to 4 instrument operating configurations

Select the programming language

Function Keys

Function access command menus that let you:

Enable or disable the output

Select metering functions

Program output voltage, current, and resistance

Display the protection status state

Set and clear protection functions

Set the output state at power-on

Calibrate the dc source

Select the output compensation

and

scroll through the front panel menu commands

Entry Keys

Entry keys let you:

Enter programming values

Increment or decrement programming values

and

select the front panel menu parameters

Содержание 66319B





















































































































































































Результаты поиска

Содержание 66319B

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 66319B, Руководство пользователя

Результаты поиска

Содержание 66319B

Отзывы:

Бренды по названию

Популярные бренды