manualshive.com logo in svg

Agilent Technologies 66319B, Руководство пользователя

Поделиться
Скачать
Agilent Technologies 66319B Скачать руководство пользователя страница 160

B - Performance, Calibration, and Configuration  

 

160 

To access the front panel commands for the configuration function, the calibration state must be enabled.  
If a calibration password is set, the password must be provided to enable calibration.  Once calibration is 
enabled, the front panel will be in Meter mode. The configuration function can only be invoked while in 
meter mode. If for some reason the front panel is not in meter mode, press the 

Meter

 key. To access the 

configuration menu, you must then simultaneously press the 

Local

 and the 

Recall

 keys.  

The Configuration function consists of the following menu commands. 

 

Press this key to access the calibration menu. 

 

Simultaneously press these keys to access the configuration menu. 

 Display 

Command 

Function 

 

CFG EXIT 

Exits the configuration menu and returns to meter mode. Also 
exits calibration mode. Changes not previously saved are lost. 

 

CFG:FACTORY 

Returns the *RST state to the factory default settings. 

 

CFG:COMP <char> 

Sets the output compensation mode. 

 

CFG:COUP <char> 

Sets the output coupling mode. 

 

CFG:RELAY1<char> 

Sets the output 1 relay mode (Option 521 units only). 

 

CFG:RELAY2<char> 

Sets the output 2 relay mode (Option 521 units only). 

 

CFG:OVP <char> 

Sets the overvoltage protection mode. 

 

CFG:SAVE  

Stores the current settings in nonvolatile RAM. 

 

CFG:UNDO  

Cancels any changes that have been made but not yet saved. 

 

 

Notes:

 

char = a character string parameter 

 

Use           and             to scroll through the menu commands. 

 

Use           and             to scroll through the menu parameters. 

Once the configuration function is started, the front panel will remain in the configuration mode. No other 
functions can be accessed from the keypad. To exit the configuration function, the CFG:EXIT command 
must be executed. Each configuration command is only executed after the 

Enter

 key is pressed.  An 

“OKAY” message is displayed to indicate that an action has been taken. When the configuration 
parameters are changed, they are not immediately stored into non-volatile memory. To store the change 
into non-volatile memory, the CFG:SAVE command must be executed  

Note that the unit is put into the present *RST state upon entering and exiting the configuration function. 

Cal

 

Shift

 

Recall

 

Local

 

T

 

S

 

Å

 

Æ

 

Содержание 66319B





















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды