AeroWorks 30cc BRAVATA ARF-QB Скачать руководство пользователя страница 5

Страница: 5 / 58

Aeroworks 30cc Laser 200 Assembly Manual

Receiver Power System:

The Aeroworks 20cc-30cc Power Package is recom-
mended. The package consists of the following
items:

◊

1 -

Fromeco Sahara Regulator w/Deans in 2 JR out

◊

1 -

Fromeco 2600mah Li-Ion Battery w/ Deans

◊

1 -

Smart-Fly Super Switch HD w/ Deans

Ignition Power System:

If using the DLE 30 or any other gas engine the
Aeroworks Ignition Power System is recommended

◊

1 - Fromeco 2600mah Li-Ion Battery w/

Universal Connector

◊

1 - Smart-Fly Ignition Regulator

◊

1 - MPI charge switch

Recommended Extensions:

22 AWG extensions are recommended throughout
the 30cc Laser 200. The following sizes will be
used:

◊

2 - 3” Extensions For Receiver to Ailerons

◊

2 - 6” Extensions For Ailerons

◊

2 - 24” Extensions For Elevators

TOOLS & ADHESIVES NEEDED

TO COMPLETE

•

Allen wrenches US and Metric.

•

Electric drill and selection of bits

•

Razor saw

•

Flat head screwdriver

•

Hobby heat gun

•

Hobby iron and covering sock

•

Masking tape

•

Modeling knife

•

Needle nose pliers or crimping tool

•

Paper towels

•

Pen, pencil or felt tipped marker

•

Phillips screwdriver

•

Ruler and tape measure

•

Scissors

•

T pins

•

Wire Cutters

•

Blue Loctite

•

CA kicker (optional)

•

Thick, Thin and Medium CA

•

Rubbing alcohol

•

Wipes

WARNING

Some rubbing alcohols

may attack painted parts.

Содержание 30cc BRAVATA ARF-QB



























































Результаты поиска

Содержание 30cc BRAVATA ARF-QB

Отзывы:

Похожие инструкции для 30cc BRAVATA ARF-QB

Бренды по названию

Популярные бренды

AeroWorks 30cc BRAVATA ARF-QB, Инструкция по сборке

Результаты поиска

Содержание 30cc BRAVATA ARF-QB

Отзывы:

Похожие инструкции для 30cc BRAVATA ARF-QB

Бренды по названию

Популярные бренды