AeroWorks 30cc BRAVATA ARF-QB Скачать руководство пользователя страница 15

Страница: 15 / 58

Aeroworks 30cc Laser 200 Assembly Manual

2. Assemble the ball links between the control

horns as shown. Secure with nylon lock nut.

RUDDER CONTROL HORN

INSTALLATION

1. Gather the rudder control horn parts as shown

below.

Required Parts

◊

2 - 4-40 ball link assemblies

◊

2 - Lock nuts

◊

2 - Left control horns

◊

2 - Right control horns

◊

6 - 2.6x16mm Phillip head bolts

◊

6 - 2mm Nuts

Required Tools and Adhesives

◊

1 - 5/64” Ball Driver

◊

1 - 3/32” Ball Driver

◊

1 - Pushrod Adjustment Wrench

◊

1 - Phillips Screw Driver

◊

1 - 1oz Bottle Gap Filling CA Glue

3. Align the control horns over the factory drilled

holes.

4. Pass the 2x16mm Phillips head bolts through

one control horn and then through the pre-drilled
holes in the rudder.

5. Install the remaining control horn and secure in

place with six 2mm nuts

6. Secure nuts with a drop of thick CA. This will

prevent them from coming loose in flight.

2. Prep all hinges for installation by applying Vase-

line petroleum jelly or light oil to the hinge joint.

This ensures no epoxy gets into the hinge during
assembly.

ELEVATOR/RUDDER HINGE

INSTALLATION

Gather elevator and rudder hinge installation
items listed below:

Required Parts

◊

1 - Rudder

◊

2 - Elevator Halves

◊

14 - Pin Point Hinges

(Not Glued)

Required Tools and Adhesives

◊

30 Minute Epoxy

◊

Mixing Sticks

◊

Mixing Cups

◊

Rubbing Alcohol

◊

Petroleum Jelly or Light Oil

Содержание 30cc BRAVATA ARF-QB



























































Результаты поиска

Содержание 30cc BRAVATA ARF-QB

Отзывы:

Похожие инструкции для 30cc BRAVATA ARF-QB

Бренды по названию

Популярные бренды

AeroWorks 30cc BRAVATA ARF-QB, Инструкция по сборке

Результаты поиска

Содержание 30cc BRAVATA ARF-QB

Отзывы:

Похожие инструкции для 30cc BRAVATA ARF-QB

Бренды по названию

Популярные бренды