AeroWorks 30cc BRAVATA ARF-QB Скачать руководство пользователя страница 29

Страница: 29 / 58

Aeroworks 30cc Laser 200 Assembly Manual

3. Align mounting template with firewall and tape in

place.

2. Locate the laser cut engine mounting template for

the DLE 30, DLE 35RA, or universal

Note:

If other engines are used a universal template
has been provided to fit your engine selection.

5. Use mounting bolts, spacer and flat fender wash-

ers to mount engine to firewall.

6. Use blue Loctite to secure the engine mounting

bolts in place. This will insure that the mounting
bolts stay in place over time.

4. Use a 3/16” drill bit to drill the engine mounting

holes in firewall.

ENGINE INSTALLATION

1. The 30cc Laser 200 will accept a wide range of

engine types. The DLE 35RA engine with
stock Muffler was used for the test flights.
Gather the following items needed for engine
installation:

Required Parts

◊

3 - Plywood Mounting Templates

◊

4 - 6.5mm Aluminum Spacers

Required Parts -Not Included

◊

1 - 30cc - 35cc Engine: DLE 35RA Shown

◊

4 - DLE 35 Standoffs w/ Mounting Bolts

◊

4 - 1/2” Diameter Fender Washers

Required Tools and Adhesives

◊

1 - Pencil

◊

1 - Masking Tape

◊

1 - Electric Drill

◊

1 - 3/16” Drill Bit

Содержание 30cc BRAVATA ARF-QB



























































Результаты поиска

Содержание 30cc BRAVATA ARF-QB

Отзывы:

Похожие инструкции для 30cc BRAVATA ARF-QB

Бренды по названию

Популярные бренды

AeroWorks 30cc BRAVATA ARF-QB, Инструкция по сборке

Результаты поиска

Содержание 30cc BRAVATA ARF-QB

Отзывы:

Похожие инструкции для 30cc BRAVATA ARF-QB

Бренды по названию

Популярные бренды