manualshive.com logo in svg

Aerotech Ndrive ML Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Ndrive ML Series Скачать руководство пользователя страница 84

Ndrive ML

Maintenance

5.1. Preventative Maintenance

The Ndrive ML and external wiring should be inspected monthly. Inspections may be required at more
frequent intervals, depending on the environment and use of the system.

D A N G E R : To minimize the possibility of bodily injury or death, disconnect all electrical
power prior to performing any maintenance or making adjustments to the equipment.

Table 5-2:

Preventative Maintenance

Check

Action to be Taken

Visually Check chassis for loose or damaged parts
/ hardware.

Note

: Internal inspection is not required.

Parts should be repaired as required. If internal
damage is suspected, these parts should be
checked and repairs made if necessary.

Inspect cooling vents.

Remove any accumulated material from vents.

Check for fluids or electrically conductive material
exposure.

Any fluids or electrically conductive material must
not be permitted to enter the Ndrive ML.

Visually inspect all cables and connections.

Tighten or re-secure any loose connections.
Replace worn or frayed cables. Replace broken
connectors.

Cleaning 

The Ndrive ML chassis can be wiped with a clean, dry, soft cloth. The cloth may be slightly moistened if
required with water or isopropyl alcohol to aid in cleaning if necessary. In this case, be careful not to allow
moisture to enter the Ndrive ML or onto exposed connectors / components. Fluids and sprays are not
recommended because of the chance for internal contamination, which may result in electrical shorts and/or
corrosion. The electrical power must be disconnected from the Ndrive ML while cleaning. Do not allow
cleaning substances or other fluids to enter the Ndrive ML or to get on to any of the connectors. Avoid
cleaning labels to prevent removing the label information.

84

Chapter 5

www.aerotech.com

Содержание Ndrive ML Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды