manualshive.com logo in svg

Aerotech Ndrive ML Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Ndrive ML Series Скачать руководство пользователя страница 40

40

Chapter 2

www.aerotech.com

2.3.3.1. Stepper Motor Phasing

N O T E :

If using standard Aerotech motors and cables, motor and encoder connection adjustments are

not required.

A stepper motor can be run with or without an encoder. If an encoder is not being used, phasing is not
necessary. With an encoder, test for proper motor phasing by running a positive motion command.

If there is a positive scaling factor (determined by the CountsPerUnit parameters) and the motor moves in a
clockwise direction, as viewed looking at the motor from the front mounting flange, the motor is phased
correctly. If the motor moves in a counterclockwise direction, swap the motor leads and re-run the
command.

Proper motor phasing is important because the end of travel (EOT) limit inputs are relative to motor rotation.

Figure 2-15:

Clockwise Motor Rotation

N O T E :

 After the motor has been phased, use the ReverseMotionDirection parameter to change the dir-

ection of “positive” motion.

Ndrive ML

Installation and Configuration

Содержание Ndrive ML Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды