manualshive.com logo in svg

Aerotech Ndrive ML Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Ndrive ML Series Скачать руководство пользователя страница 63

-IO Expansion Board

Ndrive ML

3.2. Brake Relay Connector (TB201)

TB201 is the power supply connection to the onboard solid state brake control relay.The relay can be used to
automatically control a fail-safe brake on a vertical axis. It can also be used as a general purpose output.

The brake is typically wired directly to the Motor Feedback connector and the brake power supply is
connected to TB201 (shown in

Figure 3-2

). The brake may also be connected in series with the Brake Power

Supply and interlocked using Motor Feedback brake pins (

Figure 3-3

). A varistor must be connected across

the brake to minimize high voltage transients.

The brake output can be software configured; refer to the A3200 Help file for more information (see topics for
the EnableBrakeControl parameter and the BRAKE command).

N O T E :

The brake power supply must be externally fused.

The user must verify that the brake power requirements are within the specifications of the brake control
relay.

Table 3-2:

Relay Specifications

Solid State Relay Rating

Maximum Voltage

24 VDC

Maximum Current

2.5 Amps

Turn-On/Turn-Off Time

< 3.2 ms Turn-On (typical) / 0.1 ms Turn-Off (typical)

W A R N I N G : Do not exceed the maximum specifications.

Table 3-3:

Brake Relay Connector Pinout (TB201)

Pin#

Description

In/Out/Bi

1

Brake Power Supply (+)

Input

2

Brake Power Supply (-)

Input

Table 3-4:

Mating Connector Part Numbers for the Brake Relay Connector (TB201)

Type

Aerotech P/N

Phoenix P/N

Wire Size: AWG [mm

2

]

4-Pin Terminal Block

ECK01293

1881341

20-28 [0.5- 0.080]

www.aerotech.com

Chapter 3

63

Содержание Ndrive ML Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды