manualshive.com logo in svg

Aerotech Ndrive ML Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Ndrive ML Series Скачать руководство пользователя страница 83

Maintenance

Ndrive ML

Chapter 5: Maintenance

Except for S1, the Ndrive ML does not have any user-configurable switches or jumpers.

D A N G E R : Always disconnect the Mains power connection before opening the Ndrive ML
chassis.

D A N G E R : Before performing any tests, be aware of lethal voltages inside the controller and
at the input and output power connections. A qualified service technician or electrician should
perform these tests.

Table 5-1:

LED Description

LED

Description

ENB/FLT

Turns green to indicate that the axis is enabled. Turns red to indicate a fault condition. The
ENB/FLT LED will flash between RED and GREEN if the drive is enabled and in a fault
condition.

MARKER

Turns green to indicate that the marker input is high.

CTL*

Turns green when power is applied.

POS

Turns green to indicate that the axis is in position.

* If the power light flashes continuously and the unit does not operate, there is too much current draw from the 5V power supply or
the control supply voltage level is low.

www.aerotech.com

Chapter 5

83

Содержание Ndrive ML Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды