manualshive.com logo in svg

Aerotech Ndrive ML Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Ndrive ML Series Скачать руководство пользователя страница 71

-IO Expansion Board

Ndrive ML

3.5. Opto Out Connector (Digital Outputs) (TB204)

The digital outputs are optically-isolated and can be connected in sourcing or sinking configurations. The
digital outputs are designed to connect to other ground referenced circuits and are not intended to provide
high-voltage isolation.

The outputs are software-configurable and must be connected in either all sinking or all sourcing mode.

Figure 3-10

and

Figure 3-11

illustrate how to connect to an output in current sourcing and current sinking

modes.

The opto-isolator's common connections can be directly connected to the drive's power supply; however,
doing so will effectively defeat the isolation and will reduce noise immunity.

Table 3-14:

Digital Output Specifications (TB204)

Opto Device Specifications

Value

Maximum Voltage

24 V maximum

Maximum Sink/Source Current

60 mA/channel @ 50°C

Output Saturation Voltage

2.75 V at maximum current

Output Resistance

33 Ω

Rise / Fall Time

250 usec (typical)

Reset State

Output Off (High Impedance State)

N O T E :

Power supply connections must always be made to both the Output Common Plus (OP) and

Output Common Minus (OM) pins as shown in

Figure 3-10

and

Figure 3-11

.

Table 3-15:

Opto Out Connector Pinout TB204) 

Pin#

Description

In/Out/Bi

1

Digital Output Common Plus

Input

2

Digital Output Common Minus

Input

3

Digital Output 0 (Optically-Isolated)

Output

4

Digital Output 1 (Optically-Isolated)

Output

5

Digital Output 2 (Optically-Isolated)

Output

6

Digital Output 3 (Optically-Isolated)

Output

7

Digital Output 4 (Optically-Isolated)

Output

8

Digital Output 5 (Optically-Isolated)

Output

9

Digital Output 6 (Optically-Isolated)

Output

10

Digital Output 7 (Optically-Isolated)

Output

Table 3-16:

Mating Connector for the Opto Out Connector (TB204)

Aerotech P/N

Phoenix P/N

Wire Size: mm

2

[AWG]

10-Pin Terminal Block

ECK01294

1881406

0.5-0.080 [20-28]

Suppression diodes must be installed on outputs driving relays or other inductive devices. This protects the
outputs from damage caused by inductive spikes. Suppressor diodes, such as the 1N914, can be installed
on all outputs to provide protection. It is important that the diode be installed correctly (normally reversed
biased). Refer to

Figure 3-11

for an example of a current sinking output with diode suppression and

Figure 3-

10

for an example of a current sourcing output with diode suppression.

www.aerotech.com

Chapter 3

71

Содержание Ndrive ML Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды