Aerotech Ndrive ML Series Скачать руководство пользователя страница 20

Страница: 20 / 92

Chapter 1

www.aerotech.com

1.2. Electrical Specifications

The safe operating range is load dependent.

Table 1-6:

Electrical Specifications

Description

ML 10

Motor Supply

Input Voltage

±40 VDC (max)

Input Current
(continuous)

5 A

Input Current (peak)

10 A

Input Current

Refer to

Section 1.2.1. System Power Requirements

Control Supply

Input Voltage

24 VDC typical (18-36 VDC)

Input Current

700 mA (max)

Output Voltage

(1)

±38V @ 10 A

Peak Output Current

(2)

Continuous Output Current

(2)

Power Amplifier Bandwidth

2500 Hz maximum (software selectable)

Minimum Load Resistance

0.5 Ω

Output Impedance

0.2 Ω (each phase)

User Power Supply Output

5 VDC (@ 500 mA)

Modes of Operation

Brushless; Brush; Stepper

Protective Features

Peak current limit; Over temperature; RMS current limit;
Dynamic power dissipation limit

Isolation

Isolation between control and power stages.

1. Load Dependent
2. Peak and continuous output current is load dependent (the amplifier will limit its output current based on motor speed and motor
resistance).

Ndrive ML

Introduction

Содержание Ndrive ML Series





























































































Результаты поиска

Содержание Ndrive ML Series

Отзывы:

Бренды по названию

Популярные бренды

Aerotech Ndrive ML Series, Руководство по оборудованию

Результаты поиска

Содержание Ndrive ML Series

Отзывы:

Бренды по названию

Популярные бренды