manualshive.com logo in svg

Aerotech Ndrive ML Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Ndrive ML Series Скачать руководство пользователя страница 15

Introduction

Ndrive ML

Chapter 1: Introduction

Aerotech’s Ndrive ML (Ultra-Compact "Micro" Linear) network digital drive is a high performance linear
amplifier designed to eliminate the nonlinearities common with PWM amplifiers. The drive provides
deterministic behavior, auto-identification, and easy software setup. The Ndrive ML’s high performance
double precision floating point DSP controls the digital PID and current loops. All system configuration is
done using software-settable parameters, including control loop gains and system safety functions.

The Ndrive ML is offered with an optional encoder interpolation feature (-MXH or -MXU), an auxiliary square
wave encoder input for dual loop control, dedicated analog and digital I/O (expandable with the -IO option),
and separate power connections for motor and control supply voltages.

Figure 1-1:

Ndrive ML Networked Digital Drive

www.aerotech.com

Chapter 1

15

Содержание Ndrive ML Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды