manualshive.com logo in svg

Aerotech Ndrive ML Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Ndrive ML Series Скачать руководство пользователя страница 74

74

Chapter 3

www.aerotech.com

3.6. Auxiliary Encoder Channel/PSO Output (J201)

The auxiliary encoder interface accepts an RS-422 differential quadrature line driver signal. Invalid or
missing signals will cause a feedback fault when the axis is enabled.

This encoder channel can be used as an input for master/slave operation (handwheel) or for dual feedback
systems. The auxiliary encoder interface does not support analog encoders and cannot be used as an input
for the -MXH or -MXU option.

The auxiliary encoder channel can also be used to echo the standard encoder signals or as the PSO output.
Configuring the PSO hardware will automatically configure this encoder channel as an output (refer to

Section 3.6.1.

) and will remove the 180 ohm terminator resistors.

Table 3-17:

Auxiliary Encoder Specifications

Specification

Value

Encoder Frequency

10 MHz maximum (25 nsec minimum edge separation)

x4 Quadrature Decoding

40 million counts/sec

MXH Interpolation Latency

~ 3.25 µsec (analog input to quadrature output)

N O T E :

Use the EncoderDivider parameter to configure the bi-directional encoder interface on the aux-

iliary I/O connector. The EncoderDivider parameter converts the auxiliary encoder interface to an output
and defines a divisor for the encoder echo. Refer to the A3200 Help file for more information.

N O T E :

You cannot echo the standard encoder signals on the ML with the -MXU option.

Table 3-18:

Auxiliary Encoder Channel Pinout (J201)

Pin#

Description

In/Out/Bi

Connector

1

Auxiliary RS-422 Marker Pulse - / PSO Output

(1)

Bidirectional

2

Auxiliary RS-422 Encoder 

Bidirectional

3

Auxiliary RS-422 Encoder Cosine -

Bidirectional

4

Auxiliary RS-422 Encoder Sine +

Bidirectional

5

Encoder Cable Shield

N/A

6

Auxiliary RS-422 Marker Pulse +/ PSO Output

(1)

Bidirectional

7

E5 Volt Power

Output

8

Encoder Power Common

N/A

9

Auxiliary RS-422 Encoder Sine -

Bidirectional

(1) For PSO, see

Section 3.6.1.

Table 3-19:

Mating Connector Part Numbers for the Auxiliary Encoder Connector (J201)

J201 Adapter Cable Assembly

Aerotech P.N.

Third Party P.N.

9 Pin Standard D-style

C20931

N/A

25 Pin Standard D-style

C20932

N/A

Flying Leads

ECZ01343

Molex 83421-9042

Ndrive ML

-IO Expansion Board

Содержание Ndrive ML Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды