Aerotech Ndrive ML Series Скачать руководство пользователя страница 12

Страница: 12 / 92

www.aerotech.com

W A R N I N G : To minimize the possibility of electrical shock, bodily injury or death the
following precautions must be followed.

1. If the product is used in a manner not specified by the manufacturer, the protection

provided by the product can be impaired and result in damage, shock, injury, or death.

2. Moving parts can cause crushing or shearing injuries. Access to all stage and motor parts

must be restricted while connected to a power source.

3. Cables can pose a tripping hazard. Securely mount and position all system cables to avoid

potential hazards.

4. Do not expose this product to environments or conditions outside of the listed

specifications. Exceeding environmental or operating specifications can cause damage to
the equipment.

5. Operators must be trained before operating this equipment.
6. All service and maintenance must be performed by qualified personnel.

Ndrive ML

Electrical Safety

Содержание Ndrive ML Series





























































































Результаты поиска

Содержание Ndrive ML Series

Отзывы:

Бренды по названию

Популярные бренды

Aerotech Ndrive ML Series, Руководство по оборудованию

Результаты поиска

Содержание Ndrive ML Series

Отзывы:

Бренды по названию

Популярные бренды