Aerotech Automation1 XC2 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 96

Aerotech Automation1 XC2 Скачать руководство пользователя страница 79

4.2. Joystick Interface

Aerotech Multi-Axis Joystick (NEMA12 (IP54) rated) is powered from 5 V and has a nominal 2.5 V output
in the center detent position. Three buttons are used to select axis pairs and speed ranges. An optional
interlock signal is used to indicate to the controller that the joystick is present. Joystick control will not
activate unless the joystick is in the center location. Third party devices can be used provided they
produce a symmetric output voltage within the range of -10 V to +10 V.

Connecting joystick with an Aerotech cable, all Aerotech cables are labeled to identify the connector and
connections. The joystick parameters must be set to match the analog and digital I/O connections.

The following drawings illustrate how to connect a single- or two-axis joystick. Refer to the Help file for
programming information about how to change joystick parameters.

Figure 4-2:

Two Axis Joystick Interface

XC2 Hardware Manual

4.2. Joystick Interface

www.aerotech.com

79

«
...
77
78
79
80
81
...
»

Содержание Automation1 XC2

































































































Отзывы:

Нет отзывов