Aerotech Automation1 XC2 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 96

Aerotech Automation1 XC2 Скачать руководство пользователя страница 32

2.2.1. Brushless Motor Connections

The configuration shown in

is an example of a typical brushless motor connection.

Figure 2-3:

Brushless Motor Configuration

Table 2-7:

Wire Colors for Aerotech-Supplied Brushless Motor Cables

Pin

Wire Color Set 1

(1)

Wire Color Set 2

Wire Color Set 3

Wire Color Set 4

Green/Yellow &

Shield

(2)

Green/Yellow &

Shield

Green/Yellow &

Shield

Green/Yellow &

Shield

A

Black

Blue & Yellow

Black #1

Black & Brown

B

Red

Red & Orange

Black #2

Red & Orange

C

White

White & Brown

Black #3

Violet & Blue

(1) Wire Color Set #1 is the wire set typically used by Aerotech.
(2) “&” indicates two wires (Red & Orange); “ / ” indicates a single wire (Green/White).

Brushless motors are commutated electronically by the controller. The use of Hall effect devices for
commutation is recommended.

The controller requires that the Back-EMF of each motor phase be aligned with the corresponding Hall-
effect signal. To ensure proper alignment, motor, Hall, and encoder connections should be verified using
one of the following methods:

powered

, through the use of a test program; or

unpowered

using an

oscilloscope. Both methods will identify the A, B, and C Hall/motor lead sets and indicate the correct
connections to the controller. Refer to

Section 2.2.1.1.

for powered motor phasing or

Section 2.2.1.2.

for unpowered motor and feedback phasing.

For Aerotech-supplied systems, the motor, encoder and Hall sensors are correctly configured and
connection adjustments are not necessary.

A motor filter module can be installed between the drive and the motor to reduce the effects on
PWM generated noise currents.

2.2.1. Brushless Motor Connections

XC2 Hardware Manual

32

www.aerotech.com

«
...
30
31
32
33
34
...
»

Содержание Automation1 XC2

































































































Отзывы:

Нет отзывов