Aerotech Automation1 XC2 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 96

Aerotech Automation1 XC2 Скачать руководство пользователя страница 38

2.2.3.1. Stepper Motor Phasing

A stepper motor can be run with or without an encoder.

Without an Encoder:

You do not need to phase the motor.

With an Encoder:

Because the end of travel (EOT) limit inputs are relative to motor rotation,

it is important to phase the motor.

Run a positive motion command. The motor is phased correctly if there is a positive scaling factor
(determined by the CountsPerUnit parameters) and the motor moves in a clockwise direction when you
view the motor from the front mounting flange (

). If the motor moves in a counterclockwise

direction, swap the motor leads and re-run the command. After the motor has been phased, if you want
to change the direction of positive motion, use the ReverseMotionDirection parameter.

Figure 2-11:

Positive Motor Direction

For Aerotech-supplied systems, the motor, encoder and Hall sensors are correctly configured and
connection adjustments are not necessary.

2.2.3. Stepper Motor Connections

XC2 Hardware Manual

38

www.aerotech.com

«
...
36
37
38
39
40
...
»

Содержание Automation1 XC2

































































































Отзывы:

Нет отзывов