Aerotech Automation1 XC2 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 96

Aerotech Automation1 XC2 Скачать руководство пользователя страница 57

Non-standard STO delay times are provided by special factory order. In this case, the non-standard STO
delay time is indicated by a label placed on the slice amplifier’s main connector (STO DELAY = xx sec).

Table 2-28:

STO Signal Delay

Value

STO Time Delay

450-550 msec

Table 2-29:

Motor Function Relative to STO Input State

STO 1

STO 2

Motor Function

Unpowered

Unpowered

No force/torque

Unpowered

(1)

Powered

(1)

No force/torque

Powered

(1)

Unpowered

(1)

No force/torque

Powered

Powered

Normal Operation

1. This is considered a Fault Condition since STO 1 and STO 2 do not match. Refer to

2.4.3. STO Startup Validation Testing

Verify the state of the STO 1 and STO 2 channels by manually activating the external STO hardware. Each
STO channel must be tested separately in order to detect potential short circuits between the channels.
The current state of the STO 1 and STO 2 inputs is shown in the Status Utility. A “–” indicates that the
STO input is powered by a high voltage level (24 V). An “ON” indicates that the voltage source has been
removed from the input (open circuit or 0 V), and that the STO channel is in the safe state.

DANGER

: The STO circuit does not remove lethal voltage from the motor terminals. AC

mains power must be removed before servicing.

XC2 Hardware Manual

2.4. Safe Torque Off Input (STO)

www.aerotech.com

57

«
...
55
56
57
58
59
...
»

Содержание Automation1 XC2

































































































Отзывы:

Нет отзывов