Aerotech Automation1 XC2 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 96

Aerotech Automation1 XC2 Скачать руководство пользователя страница 30

2.1.3. Minimizing Noise for EMC/CE Compliance

IMPORTANT

: The XC2 is a component designed to be integrated with other electronics.

EMC testing must be conducted on the final product configuration.

To reduce electrical noise, observe the following motor feedback and input power wiring techniques.

1. Use shielded cable for motor and feedback connectors. Connect the shield to the backshell at

each end of the cable.

2. Separate motor and power wiring from encoder and I/O wiring.
3. Mount drives, power supplies, and filter components on a conductive panel. Keep wire-run

lengths to a minimum. For the AC power lines feeding the VDC Motor supply and VDC Control sup-
ply, place a line filter, such as Schaffner FN2070-10-06 (Aerotech# ECZ00284) between the VDC
power supply’s AC inputs and the AC power source.

4. Use the lowest motor voltage required by the application to reduce radiated emission.
5. Use a separate wire for each ground connection to the drive. Use the shortest possible wire

length.

For additional XC2 system interconnection information, refer to

Section 2.6. System

Interconnection

.

2.1.3. Minimizing Noise for EMC/CE Compliance

XC2 Hardware Manual

30

www.aerotech.com

«
...
28
29
30
31
32
...
»

Содержание Automation1 XC2

































































































Отзывы:

Нет отзывов