Aerotech Automation1 XC2 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 96

Aerotech Automation1 XC2 Скачать руководство пользователя страница 13

Safety Procedures and Warnings

IMPORTANT

: This manual tells you how to carefully and correctly use and operate the XC2

drive.

l

Read all parts of this manual before you install or operate the XC2 drive or before
you do maintenance to your system.

l

To prevent injury to you and damage to the equipment, obey the precautions in this
manual.

l

All specifications and illustrations are for reference only and were complete and
accurate as of the release of this manual. To find the newest information about this
product, refer to www.aerotech.com.

If you do not understand the information in this manual, contact Aerotech Global
Technical Support.

IMPORTANT

: This product has been designed for light industrial manufacturing or

laboratory environments. If the product is used in a manner not specified by the
manufacturer:

l

The protection provided by the equipment could be impaired.

l

The life expectancy of the product could be decreased.

DANGER

: To decrease the risk of electrical shock, injury, death, and damage to the

equipment, obey the precautions that follow.

1. Before you do maintenance to the equipment, disconnect the electrical power.

2. Restrict access to the XC2 when it is connected to a power source.

3. Do not connect or disconnect electrical components, wires, and cables while this

product is connected to a power source.

4. Wait at least one (1) minute after removing the power supply before doing main-

tenance or an inspection. Otherwise, there is the danger of electric shock.

5. Supply each operator with the necessary protection from live electrical circuits.

6. Make sure that all components are grounded correctly and that they obey the local

electrical safety requirements.

7. Install the necessary precautions to supply safety and protection to the operator.

DANGER

: System travel can cause crush, shear, or pinch injuries. Restrict access to all

motor and stage parts while your system is connected to a power source.

WARNING

: To prevent damage to the equipment and decrease the risk of electrical shock

and injury, obey the precautions that follow.

1. Make sure that all system cables are correctly attached and positioned.
2. Do not use the cables or the connectors to lift or move this product.
3. Use this product only in environments and operating conditions that are approved

in this manual.

4. Only trained operators should operate this equipment.

XC2 Hardware Manual

Safety Procedures and Warnings

www.aerotech.com

13

«
...
11
12
13
14
15
...
»

Содержание Automation1 XC2

































































































Отзывы:

Нет отзывов