Aerotech Automation1 XC2 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 96

Aerotech Automation1 XC2 Скачать руководство пользователя страница 47

2.3.3. Thermistor Input

The thermistor input is used to detect a motor over temperature condition by using a positive
temperature coefficient sensor. As the temperature of the sensor increases, so does the resistance.
Under normal operating conditions, the resistance of the thermistor is low which will result in a low input
signal. As the increasing temperature causes the thermistor’s resistance to increase, the sensor will
trigger an over temperature fault.

The thermistor is connected between Pin 2 and Signal Common. The nominal trip value of the sensor is
1.385 kΩ. The circuit includes a 12 kΩ internal pull-up resistor which corresponds to a trip voltage of
+0.52 V.

Table 2-18:

Thermistor Input Pin on the Feedback Connector

Pin #

Description

In/Out/Bi

2

Motor Over Temperature Thermistor

Input

Figure 2-19:

Thermistor Input Schematic (Feedback Connector)

www.aerotech.com

47

XC2 Hardware Manual

2.3.3. Thermistor Input

«
...
45
46
47
48
49
...
»

Содержание Automation1 XC2

































































































Отзывы:

Нет отзывов