Aeroqual AQM60 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 83

Aeroqual AQM60 Скачать руководство пользователя страница 77

Page | 77

Aeroqual AQM60 User Guide

26. AQM sensor module parameters upload command. The command consist of two data streams
one upload invoking command 4 bytes, then followed by a parameters stream which is 50 bytes.

Command:

RECEIVER, AQM_ID, SENSOR_PARAM_UPLOAD, SENSOR_CODE

Parameters:  RECEIVER, HTR, OFFSET, TEMPRESET, TIMERESET, TEMPREAD, TIMEREAD, H0, H1,
H2, PWML, PWMH, CYCLENUM, CHECKSUM

* SENSOR_PARAM_UPLOAD - 1 byte command, its value = 0x09

26A. Acknowledge reply command 5 bytes:

MONITOR, SENSOR_PARAM_UPLOAD, SENSOR_CODE, CHECKSUM

* The reply is used for confirming the sensor parameter upload was successful

27. Get all sensor offset correction factor values command, 4 bytes:

RECEIVER, AQM_ID, GET_OFFSET_FACTOR, CHECKSUM

* GET_OFFSET_FACTOR - 1 byte command to get the AQM all configured sensor offset factors.

28. Replied offset value for all configured sensors, total 74 bytes:

MONITOR, AQM_ID, GET_OFFSET_FACTOR, SENSOR_OFFSET_VALUE,
SENSOR_OFFSET_VALUE, SENSOR_OFFSET_VALUE,
SENSOR_OFFSET_VALUE, SENSOR_OFFSET_VALUE, SENSOR_OFFSET_VALUE,
SENSOR_OFFSET_VALUE, SENSOR_OFFSET_VALUE,
SENSOR_OFFSET_VALUE, SENSOR_OFFSET_VALUE, SENSOR_OFFSET_VALUE,
SENSOR_OFFSET_VALUE, SENSOR_OFFSET_VALUE,
SENSOR_OFFSET_VALUE, CHECKSUM

* SENSOR_OFFSET_VALUE - 5 bytes each, consist of 1 byte SENSOR_CODE code, 4 bytes floating
point offset value.
Example: 0x30 00 00 00 00, this is O3 Low sensor with offset value of 0.000

29. Set offset value command, 4 bytes command followed by 9 bytes span calibration value details:

RECEIVER, AQM_ID, SET_OFFSET_FACTOR, CHECKSUM
RECEIVER, AQM_ID, SET_OFFSET_FACTOR, SENSOR_CODE, OFFSET_VALUE, CHECKSUM

* SET_OFFSET_FACTOR - 1 byte command to change the gain value
* OFFSET_VALUE - 4 bytes floating point data, specified the sensor span calibration point

Example: 0x55 01 02 93

0x55 01 02 30 3B A3 D7 0A B9

* Set offset value 0.005 for O3 sensor

29A. Acknowledge reply command of setting offset value, 4 bytes:

MONITOR, AQM_ID, SET_OFFSET_FACTOR, CHECKSUM

30. Update controller sensor list command, 4 bytes, followed by the size of the sensor list:

RECEIVER, AQM_ID, UPDATE_SENSOR_LIST, CHECKSUM

RECEIVER, AQM_ID, SENSOR_LIST_SIZE, CHECKSUM

when get the acknowledge command within 5 sec, 4 bytes:

MONITOR, AQM_ID, UPDATE_SENSOR_LIST, CHECKSUM

«
...
75
76
77
78
79
...
»

Содержание AQM60




















































































Отзывы:

Нет отзывов