manualshive.com logo in svg

Aeroqual AQM60, Руководство пользователя, Страница: 51 / 83

Поделиться
Скачать
Aeroqual AQM60 Скачать руководство пользователя страница 51

 

 

Page | 51  

Aeroqual AQM60 User Guide 

 

 
 

7.3.4.  Replacing Gas Treatment Media 

 

The scrubber media can be changed by removing the front panel from the GTM. This can be achieved 
without removing the entire GTM from the AQM. To release the front panel the two screws holding the 
scrubber must first be removed. Pull the front cover out to expose the luer gas connection inside the GTM. 
Once this gas connection has been released the media can be removed from GTM. 
 

 

   
Gently lift up the large activated carbon scrubber to expose the two screws which are holding the media on 
to the GTM front panel.  
 

 

 
 
Disconnect the gas connection from the wall of the GTM front panel. Once this has been done then the 
media can be removed and replaced with a new media kit.  To install the new kit, simply reverse this 
process. 
 

Note: Remember to reconnect the luer connection before inserting the front panel back into the GTM 
housing.

 

 

 

 

 
 
 
 

Содержание AQM60




















































































Отзывы:

Нет отзывов