manualshive.com logo in svg

Aeroqual AQM60, Руководство пользователя, Страница: 56 / 83

Поделиться
Скачать
Aeroqual AQM60 Скачать руководство пользователя страница 56

 

 

Page | 56  

Aeroqual AQM60 User Guide 

 

 
 

7.4.7.  Laser Current Check. 

To determine the laser current 

go to “Diagnostics” 

 

“Sensor Diagnostics View”. The column titled “PM10 

Laser (mA)

” will provide the laser current. If the laser current has drifted up or down by more than 3mA, the 

engine may need servicing; please contact Aeroqual for advice.  
 

Note: The laser current should be stable at 18 ±3 mA 

 

7.4.8.  Filter Changes 

There are two internal filters which are located on the side of the optical engine. They are designed to 
provide protection and clean purge air. These will become dirty and must be replaced periodically.  
To do this, unscrew the filters from the side of the optical engine and replace with new filters. These can be 
purchased from Aeroqual. Please contact technical support for a quotation.  
 

         

 

7.4.9.  Cyclone and Inlet Cleaning 

The dust cap of the sharp cut cyclone will accumulate particulate matter and will need to be periodically 
cleaned. Blow out the cyclone with compressed air and unscrew the dust cap and clean. Replace the cap 
tightly and ensure there are no potential leaks. 
 

         

 

 
The cyclone can be disassembled completely by removing the three Allen head screws and pulling it apart. 
The internal parts should be cleaned with isopropyl alcohol once a year.  
 

                    

 

Allen head 
screws 

Dirty 
Filter 

Purge 
Filter 

Sample 
Filter 

Clean 
Filter 

Содержание AQM60




















































































Отзывы:

Нет отзывов