Aeroqual AQM60 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 83

Aeroqual AQM60 Скачать руководство пользователя страница 62

Page | 62

Aeroqual AQM60 User Guide

8.2.

Particle Monitor/Profiler

Symptom

Possible Cause

Fault isolation/Solution

PM values seem incorrect

Sample flow incorrect

Sample and/or purge filters
dirty

Gain factors incorrect

Offset factor incorrect

Check sample flow and adjust to correct
value using flow adjusters

Replace filters

Perform span calibration

Perform zero calibration

Low Sensitivity

Laser is old

The laser current can be
measured in diagnostics mode
using AQM60 software. If
above 20 mA then fault

Laser needs replacing.

Send to your authorised distributor or
contact Aeroqual technical support.

Low Sensitivity

Dirty optics

Optics need cleaning

Send to your authorised distributor or
contact Aeroqual technical support.

High baseline (H0)

Dirty optics

Optics need cleaning

Send to your authorised distributor or
contact Aeroqual technical support.

COMMUNICATION

No communication over
RS232

RS232 cable disconnected

Control Module Failed

Reconnect cable.

Replace Control Module.

PC Data logging stopped

AQM power blackout
interrupted data logging

USB to serial hub not working

Close and restart AQM software.

Check USB connectors. Check the serial
hub is present on the device hardware
menu in the PC. If not reload driver
software and re-install.

No data on SD card

Card not correctly installed in
slot

Data logging interval set too
large

Data card module fault

Turn off AQM and install card in slot
correctly.

Set logging interval in configuration to a
lower interval.

Send control module to factory for
replacement module.

«
...
60
61
62
63
64
...
»

Содержание AQM60




















































































Отзывы:

Нет отзывов