manualshive.com logo in svg

Aeroqual AQM60, Руководство пользователя, Страница: 76 / 83

Поделиться
Скачать
Aeroqual AQM60 Скачать руководство пользователя страница 76

 

 

Page | 76  

Aeroqual AQM60 User Guide 

 

   09 

01 

18 

10:14:00 0.028  9.8 

... 

2.6 

S\n 

 

*Date, time and readings 

with tab delimited 
    
      * Sensor1 ~ SensorX - sensor name ASCII with tab delimited. 
   * 10:12:00 - 8 bytes time ASCII, hour:minutes:seconds 
   * 0.26, 10.6 - 8 bytes decimal value in ASCII 
   * S - 1 byte inlet state, S for Sample, Z for Zero air scrubber on 
 
21 Delete a file in SD card command, 4 bytes followed by 15 bytes with file name: 
 
   RECEIVER, AQM_ID, DELETE_A_FILE, CHECKSUM 
    
   * DELETE_A_FILE - 1 byte command to delete a file in data logging card. 
    
   Followed by 16 bytes stream with file name: 
       
   RECEIVER, AQM_ID, DELETE_A_FILE, FILE_NAME, CHECKSUM 
       
   * FILE_NAME - 12 bytes ASCII code of a full file name. 
 
21A. Acknowledge reply command to confirm the file delete operation was successful. 
    
   MONITOR, AQM_ID, DELETE_A_FILE, CHECKSUM 
    
22. Get sensor module version information command 4 bytes: 
 
   RECEIVER, AQM_ID, GET_SENSOR_VERSION, SENSOR_CODE 
    
   * GET_SESNOR_VERSION - 1 byte command to get sensor module version info, refer section 2 for its 
value. 
   * SENSOR_CODE - 1 byte specific sensor code 
    
23. Sensor module version info reply command 15 bytes: 
 
    
 
MONITOR, AQM_ID, GET_SENSOR_VERSION, SENSOR_CODE, VERSION_NUM, DISP_TYPE, 
NAME_LENGTH, NAME_ASCII, CHECKSUM 
    
   * GET_SESNOR_VERSION - 1 byte command to get sensor module version info, refer section 2 for its 
value. 
   * SENSOR_CODE - 1 byte specific sensor code 
   * VERSION_NUM - 1 byte sensor version number scaled up by 10, so its real number is 
VERSION_NUM/10. 
   * NAME_LENGTH - 1 byte specifies the sensor's name valid ASCII code length. 
   * NAME_ASCII - 7 byes ASCII code of sensor name, its valid length is specified by NAME_LENGTH. 
 
24. Download a specific sensor calibration parameters command, 4 bytes .  
 
   RECEIVER, AQM_ID, SENSOR_PARAM_DOWNLOAD, SENSOR_CODE 
 
25. Download parameters reply command. The command will get the sensor's all parameters. The total reply 
stream length is 50 bytes. 
 
   MONITOR, HTR, OFFSET, TEMPRESET, TIMERESET, TEMPREAD, TIMEREAD, H0, H1,  H2,  PWML, 
PWMH, CYCLENUM, CHECKSUM 
 

 

   * SENSOR_PARAM_DOWNLOAD - 1 byte command, its value = 0x18 
   * SENSOR_CODE - 1 byte sensor code. 
   * HTR, OFFSET, TEMPRESET, TIMERESET, TEMPREAD, TIMEREAD, H0, H1,  H2,  PWML, PWMH, 
CYCLENUM 
     - are 4 bytes floating point value,  
 

   

Содержание AQM60




















































































Отзывы:

Нет отзывов