Aeroflex 2030 Series Скачать руководство пользователя страница 38

Страница: 38 / 234

GENERAL INFORMATION

ACCESSORIES

When ordering please quote the full ordering number information

Ordering numbers

Supplied accessories

46882/293

AC supply lead (see ‘Power cords’, Chap 2).

Operating manual for NAV-750C (this manual).

Optional accessories

46881/978

Maintenance manual for NAV-750C.

43139/042

RF connector cable, TM 4969/3, 50

, 1.5 m, BNC.

54311/092

Coaxial adapter N male to BNC female.

59999/163

Precision coaxial adapter, N male to SMA female.

54411/051

Impedance adapter, 50 to 75

, BNC connectors.

54311/095

RF connector cable, 1 m, type N connectors.

43129/189

GPIB lead assembly.

46883/408

IEEE/IEC adapter block for GPIB socket.

46884/291

Rack mounting kit (with slides) for rack cabinets with depths
from 480 to 680 mm (18.89 to 26.77 in).

46884/292

Rack mounting kit (with slides) for rack cabinets with depths
from 680 to 840 mm(26.77 to 33.08 in).

46884/541

Rack mounting kit (without slides).

46662/525

Transit case (aluminum).

54112/164

Soft carrying case.

1-15

Содержание 2030 Series











































































































































































































































Результаты поиска

Содержание 2030 Series

Отзывы:

Похожие инструкции для 2030 Series

Бренды по названию

Популярные бренды

Aeroflex 2030 Series, Руководство по эксплуатации

Результаты поиска

Содержание 2030 Series

Отзывы:

Похожие инструкции для 2030 Series

Бренды по названию

Популярные бренды