Advantech SOM-4450 Series Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 133

background image

Advantech SOM-ETX Design Guide

5.5 VGA

SOM-ETX provides analog display signals. There are three signals -- red, green, and
blue -- that send color information to a VGA monitor. These three signals each drive
an electron gun that emits electrons which paint one primary color at a point on the
monitor screen. Analog levels between 0 (completely dark) and 0.7 V (maximum
brightness) on these control lines tell the monitor what intensities of these three
primary colors to combine to make the color of a dot (or pixel) on the monitor’s
screen.

5.5.1 Signal Description

Table 5.12 shows SOM-ETX VGA signals, including pin number, signals, I/0, power
plane, terminal resistors, damping resistors and descriptions.

Table 5.12 VGA signals description

Pin Signal I/O Description

C3 R

O

Red analog video output signal for CRT monitors. It should be
terminated with 75 ohms to ground at the video connector.

C6 G

O

Green analog video output signals for CRT monitors. It should be
terminated with 75 ohms to ground at the video connector.

C4 B

O

Blue analog video output signals for CRT monitors. It should be
terminated with 75 ohms to ground at the video connector.

C5 HSY

O

Horizontal Sync: This output supplies the horizontal synchronization
pulse to the CRT monitor.

C7 VSY

O

Vertical Sync: This output supplies the vertical synchronization pulse to
the CRT monitor.

C8 DDCK I/O

These pin can be used for a DDC interface between the graphics
controller chip and the CRT monitor

C10 DDDA

I/O

These pin can be used for a DDC interface between the graphics
controller chip and the CRT monitor

5.5.2 Design Guideline

VESA standards require the DDC_PWR line. Some VGA monitor does not support
the DDC standard. But we suggested that DDCK and DDDA signals must connect to
CRT monitor. It can be used for plug and play, monitor-type detection when standard
monitors are attached.

SOM-ETX

R

DDCK

VGA Connector

G

HSY

VSY

B

DDDA

D-Sub15

Figure 5-15 VGA Connections

Chapter 5 Carrier Board Design Guidelines

79

«
...
77
78
79
80
81
...
»

Содержание SOM-4450 Series






































































































































Отзывы:

Нет отзывов

Похожие инструкции для SOM-4450 Series

Бренд: P&E Microcomputer Systems Страницы: 59

870 Extreme3 R2.0

Бренд: ASROCK Страницы: 17

Бренд: Infineon Страницы: 24

Бренд: Biostar Страницы: 71

Бренд: ZiLOG Страницы: 41

ML501MicroBlaze

Бренд: Xilinx Страницы: 46

PCM-8152 3rd Generation

Бренд: Aaeon Страницы: 6

conga-HPC/EVAL-Server

Бренд: Congatec Страницы: 54

Бренд: ASROCK Страницы: 145

Бренд: IBASE Technology Страницы: 60

Бренд: AMD Geode Страницы: 51

Бренд: Yamaha Страницы: 223

Бренд: Commell Страницы: 53

Бренд: Texas Instruments Страницы: 20

Бренд: TYAN Страницы: 86

MAG B560M BAZOOKA

Бренд: MSI Страницы: 136

Бренд: MSI Страницы: 134

E-TEC 40RL 2008

Бренд: Evinrude Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды