manualshive.com logo in svg

Advantech SOM-4450 Series, Руководство по конструкции

Поделиться
Скачать
Advantech SOM-4450 Series Скачать руководство пользователя страница 77

Advantech SOM-ETX Design Guide 

 

B20,64,9
1,70,16,1
2,8 

DREQ[0,1
,2,3,5,6,7] 

I 

The asynchronous DMA request inputs are used by external 
devices to indicate when they need service from the CPU modules 
DAM controllers. DREQ0..3 are used for transfers between 8-bit I/O 
adapters and system memory. DREQ5..7 are used for transfers 
between 16-bit I/O adapters and system memory. DRQ4 is not 
available externally. All DRQ pins have pull-up resistors on the 
CPU modules. 

B22,66,4
6,72,18,1
4,10 

DACK[0,1,
2,3,5,6,7]# 

O 

DMA acknowledge 0..3 and 5.7 are used to acknowledge DMA 
requests. They are active-low. 

B44 TC  O 

The active-high output TC indicates that one of the DMA channels 
has transferred all data. 

- 

IRQ[3..7,9
,15] 

I 

These are the asynchronous interrupt request lines. IRQ0, 1, 2 and 
8 are not available as external interrupts because they are used 
internally on the CPU module. All IRQ signals are active-high. The 
interrupt requests are prioritized. IRQ9 through IRQ12 and IRQ14 
through IRQ15 have the highest priority (IRQ9 is the highest). IRQ3 
through IRQ7 have the lowest priority (IRQ7 is the lowest). An 
interrupt request is generated when an IRQ line is raised from low 
to high. The line must be held high until the CPU acknowledges the 
interrupt request (interrupt service routine).  

 
 
 

5.4.2 Design Guideline 

5.4.2.1 Interrupt and DMA signals  

Eight-bit ISA devices will not need the signals on the lower part of the connector (the 
C and D pin numbers),but the additional interrupts and DMA channels available on 
this part of the connector will make system configuration more flexible. 
 
Many ISA devices already contain a plug-and-play matrix that allows routing internal 
interrupt or DMA requests to most of the possible destinations on the ISA bus. For 
simpler devices, which do not implement internal interrupt and DMA routing, it is 
often worthwhile to provide jumper blocks or resistor options. 
 
These mechanical switching arrangements allow changing the devices interrupt and 
DMA assignments in case a resource conflict arises later in the development of the 
system. 
 
ISA devices generally are not able to share interrupts. Because of this, ISA device 
drivers are rarely written with interrupt sharing in mind. Systems with many ISA 
devices tend to run out of interrupt lines. Solving this problem can require specialized 
software and hardware. 
 
 

 

Chapter 5  Carrier Board Design Guidelines 

77 

 

Содержание SOM-4450 Series






































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды