Advantech SOM-4450 Series Скачать руководство пользователя страница 121

Страница: 121 / 133

Advantech SOM-ETX Design Guide

Connector Precautions for use:

1. Tolerance Clearance on Mating Side

The effective contact length of the product is set to 0.7mm. Please use the
product so as to set the clearance to less than 0.2mm between the header
and the receptacle in the mating process.

2. Fixation between Mounting Boards

The very low profile and compact product, so never fix the connector
between boards by mating force only

3. Stacking Height Tolerance for Mating

Note:

Please Note that the above stacking tolerance doesn't include the solder
paste thickness.

4. Mounting Temperature Profile (Reference)

Setting Condition:

•

Board

Size:

161x100x1.6(mm)

Material:

Glass

epoxy

•

Solder paste

Constituent: 63Sn/37Pb(Flux content: 11Wt%)

Metal Mask Thickness : 0.15mm

•

Reflow Method

IR reflow

Figure 7-4

For Hirose FX8-100S connector detail spec, please reference the Hirose website.
http://www.hirose.com/

Chapter 7 Carrier Board Mechanical Design

121

Содержание SOM-4450 Series






































































































































Результаты поиска

Содержание SOM-4450 Series

Отзывы:

Похожие инструкции для SOM-4450 Series

Бренды по названию

Популярные бренды

Advantech SOM-4450 Series, Руководство по конструкции

Результаты поиска

Содержание SOM-4450 Series

Отзывы:

Похожие инструкции для SOM-4450 Series

Бренды по названию

Популярные бренды