manualshive.com logo in svg

Advantech SOM-4450 Series, Руководство по конструкции

Поделиться
Скачать
Advantech SOM-4450 Series Скачать руководство пользователя страница 108

Advantech SOM-ETX Design Guide 

 

5.14   Miscellaneous 

5.14.1  Miscellaneous Signal Description 

 

Table 5.25 Misc signal descriptions 

Pin Signal 

Description 

I/O 

This is the PC speaker output signal from SOM-ETX module. 
Please connect this signal to the speaker. 

D6 SPKER 

I 

D8 BATT 

O 

3V backup cell input from carrier to SOM-ETX module for RTC 
operation and storage register non-volatility in the absence of 
system power. (BATT=2.4V-3.3V) 
Clock and data line of I2C-Bus. Switched I/O-lines with 
approximate 10kHz. Do not use as multi-master. Intended for 
EEPROM support and other simple I/O-devices. 

D16 

I2CCLK 

I 

D22 

I2CDAT 

Clock and data line of SM-Bus. No standard signals, please 
contact your CPU board supplier for hard-and software 
support. 

D23 

SMBCLK 

I 

D24 

SMBDAT 

D4 PWGIN 

O 

High active input from carrier to SOM-ETX module for 
indicating that power supply is ready. 
Power supply input for internal Suspend circuit. Connect to 5V 
Stand by power if available from ATX power supply. 

D3 VCCSB5V 

P 

Remove All Circuit Power Except Internal Suspend Circuit. 
PS_ON will become active high to disable all the circuits 
except internal Suspend circuit. Connect to PS-On of your ATX 
power supply. 

D5 PS-ON# 

I 

D7 PWRBTN# 

O 

Power Button Input. Connect with switch or open collector 
driver to GND for ATX power button function. 
External system-management-interrupt input. Please connect 
this signal to an external SMI event input on the SOM-ETX 
CPU module, then carrier board can doing a power 
management function. WDGACT# WatchDog active signal. 
This signal can reset the system 

D21 EXTSMI# 

I 

D90 RINGWAKE# 

Wakeup signal from carrier board to SOM-ETX CPU module. 
Please connect this pin to a wakeup pin on the SOM-ETX CPU 
module. 

O 

Boot device chip select from SOM-ETX CPU module to the 
flash memory on the carrier board. For internal use only! Do 
not connect! 

D13 ROMCS# 

I 

Boot device chip select from carrier board to SOM-ETX CPU 
module. For internal use only! Do not connect! 

D15 EXT_ROMCS# 

O 

Pull high on carrier board to inform SOM module having 
external BIOS on the carrier board. For internal use only! Do 
not connect! 

D20 GPCS 

O 

 
 
 

108 

Chapter 5  Carrier Board Design Guidelines

 

Содержание SOM-4450 Series






































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды