Advantech SOM-4450 Series Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 133

background image

Advantech SOM-ETX Design Guide

Tskew

Tskew

Vih

Vih

Vil

Vil

Vtest

Vtest

Tskew

CLK (Device 1)

CLK (Device 2)

Figure 5-2 Clock Skew Diagram

5.1.2.3 Non-necessary Signals for Individual PCI device

A PCI device implemented directly on the baseboard uses a subset of the signals
shown on the slot connector. Some pins on the slot connector are used for slot and
PCI card management functions and are not necessary for the operation of the PCI
device itself.

An individual PCI device will not have pins REQ64, ACK64,M66EN, PRSNT1,
PRSNT2, SDONE, SBO#, or the reserved pins. Most devices do not implement the
test pins TCK, TDO, TDI, TMS, and TRST. Most PCI devices use INTA# only and do
not have a connection for INTB#, INTC# or INTD#.

5.1.2.4 Carried Board PCI slots Power Requirements

All PCI connectors require four power rails: +5V, +3.3V, +12V, and -12V. Systems
that provide PCI connectors are required to provide all four rails in every system with
the current budget. Systems may optionally supply 3.3Vaux power. Systems that do
not support PCI bus power management must treat the 3.3Vaux pin as reserved.
There are no specific system requirements for current per connector on the 3.3V and
5V rails; this is system dependent. Note that an add-in card must limit its total power
consumption to 25 watts (from all power rails). The system provides a total power
budget for add-in cards that can be distributed between connectors in an arbitrary
way. The PRSNTn# pins on the connector allow the system to optionally assess the
power demand of each add-in card and determine if the installed configuration will
run within the total power budget.

Table 5.4 Maximum Add-in Card Loading via Each Power Rail

Power Rail

Add-in card

3.3V+/-0.3V

7.6A Max (System dependent)

5V+/-5%

5A Max (System dependent)

12V+/-5%

500mA Max.

-12V+/-5%

100mA Max.

64

Chapter 5 Carrier Board Design Guidelines

«
...
62
63
64
65
66
...
»

Содержание SOM-4450 Series






































































































































Отзывы:

Нет отзывов

Похожие инструкции для SOM-4450 Series

Бренд: Zapi Страницы: 50

Бренд: ASROCK Страницы: 128

Бренд: TYAN Страницы: 64

Бренд: QDI Страницы: 20

Fatal1ty Z87 Killer Series

Бренд: ASROCK Страницы: 102

Бренд: BESTEK Страницы: 47

DUOX Programmer

Бренд: Fermax Страницы: 99

Бренд: MSI Страницы: 112

K8N Neo3 MS-7135

Бренд: MSI Страницы: 124

Бренд: IEI Technology Страницы: 145

Бренд: TYAN Страницы: 86

Бренд: Gigabyte Страницы: 96

Бренд: SOLTEK Страницы: 94

Бренд: ECS Страницы: 70

Бренд: Aaeon Страницы: 46

Бренд: Aaeon Страницы: 48

Бренд: Aaeon Страницы: 53

Бренд: Aaeon Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды