ADTRAN 1200410L2 Скачать руководство пользователя страница 66

Страница: 66 / 80

Chapter 8. Example Operations

ESU LT User Manual

61200410L2-1A

When you have finished viewing the results, complete the
following steps to return the ESU LT to normal operation:

Table 8-1. Initiating a Remote Loopback

Step

Action

Select

EST

from the main menu.

Use the

up and down arrows to place the cursor on

EST

Press

Enter

to select.

Result

: The first two

EST

submenu items display.

Using the up and down arrows

place the cursor on

ETWORK

ESTS

Press

Enter

to enter the

ETWORK

EST

menu.

Result

Beginning display of the submenu items. Each menu item can be

selected with the

up and down arrows.

Use the up and down arrows to place the cursor on

EMOTE

OOPBK

Press

Enter

to select FE1 Loopback.

Use the up and down arrows to select

EST

ATTERN

Press

Enter

again to activate the

EST

ATTERN

submenu.

Use the up and down arrows to select

511 ACT TS0

(

QRSS ACT TS0

is also an available test pattern.)

Press

Enter

to activate the selection.

Result:

The ESU LT always checks for 511 errors. The results of this check are shown

under submenu item 4.

Step

Action

Press

Cancel

to return to submenu item

EST

ATTERN

Select

ATTERN

to terminate the test and the 511 pattern genera-

tion.

Result

: The far end remains in loopback until the network

EMOTE

OOPBK

set to

OOPBACK

under submenu item

EMOTE

OOPBK

Содержание 1200410L2

















































































Результаты поиска

Содержание 1200410L2

Отзывы:

Похожие инструкции для 1200410L2

Бренды по названию

Популярные бренды

ADTRAN 1200410L2, Руководство пользователя

Результаты поиска

Содержание 1200410L2

Отзывы:

Похожие инструкции для 1200410L2

Бренды по названию

Популярные бренды