ADTRAN 1200410L2 Скачать руководство пользователя страница 61

Страница: 61 / 80

Chapter 7. Test Menu

61200410L2-1A

ESU LT User Manual

511 Active TS0s

The 511 pattern is generated and checked by the Nx56K/64K serial
interface. It only appears in the TS0s assigned to the Nx56K/64K
port.

When used in conjunction with the payload loopback at the far end,
an end-to-end integrity check can be made on the DTE ports.

All Zeros

Generates an all zeros pattern in every channel.

All Ones

Generates an all ones pattern in every channel.

CLR ERRORS

RRORS

has two functions.

1. To clear out the 511 error total when you press

Enter

To display a total of the 511 errors. If 511 errors are being
received, the display is updated accordingly. See Figure 7-5.

Figure 7-5. Clear Errors Screen

This menu function is very useful for testing end-to-end integrity of
the network. First loop up the far end ESU LT. Then send a 511
pattern from the local ESU LT. The

CLR ERRORS

screen can then

be used to determine whether the link is functioning properly by
verifying that no errors are being counted.

INSERT QRSS OR 511 ERRORS

When running a 511 or QRSS pattern test, press

NTER

to insert an

error into the pattern.

Содержание 1200410L2

















































































Результаты поиска

Содержание 1200410L2

Отзывы:

Похожие инструкции для 1200410L2

Бренды по названию

Популярные бренды

ADTRAN 1200410L2, Руководство пользователя

Результаты поиска

Содержание 1200410L2

Отзывы:

Похожие инструкции для 1200410L2

Бренды по названию

Популярные бренды