ADTRAN 1200410L2 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 80

background image

Chapter 5. Configuration Menu

61200410L2-1A

ESU LT User Manual

49

TS0

Selects a full 56/64K TS0 as the management channel. The
management channel is automatically allotted to the first active
TS0, and the DTE clock rate decreases by either 56K or 64K
(depending on the Nx configuration). For example, on a full E1
circuit with TS0 management enabled, channel 1 is the
management channel and the DTE clock rate will drop from 1984K
to 1920K.

On a fractional E1 with channels 3 and 4 mapped and TS0
management enabled, channel 3 will be the management channel
and the DTE clock rate would drop from 128K to 64K.

TS0 management is not available in unframed mode.

Port (Port Configuration)

The menu item

P

ORT

is used to select and then to configure the

parameters associated with the high-speed serial interface.

Interface

This option sets the electrical interface for the Nx56/64 port.

TS0 Rate

This sets the base rate of the interface. The actual data rate depends
on the number of time slots used.
Choices:

56K

;

64K

Mapping

This sets the unit to use alternate or contiguous channels in the E1
data stream. If more than 16 channels are used in CCS mode,
contiguous must be used. If more than 15 channels are used in CAS
mode, contiguous must be used. If other than a private network is
used, the carrier must be notified of this choice.
Choices:

ALT

(alternate);

CONT

(contiguous)

«
...
47
48
49
50
51
...
»

Содержание 1200410L2

















































































Отзывы:

Нет отзывов

Похожие инструкции для 1200410L2

Бренд: D-Link Страницы: 13

NetDefend DFL-260E

Бренд: D-Link Страницы: 328

ShareCenter Pulse DNS-320

Бренд: D-Link Страницы: 2

DFL-210 - NetDefend - Security Appliance

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 22

Бренд: D-Link Страницы: 4

Бренд: Dahua Страницы: 12

NetDefend DFL-1600

Бренд: D-Link Страницы: 23

Бренд: NavigateWorx Страницы: 71

Бренд: Parkside Страницы: 55

Бренд: Parkside Страницы: 34

Z3-DM8168-PCI-RPS

Бренд: Z3 Technology Страницы: 20

Z3-DM8107-SDI2-RPS

Бренд: Z3 Technology Страницы: 75

Бренд: Z-Wave Страницы: 13

Бренд: Conceptronic Страницы: 2

AT-9424Ts/XP AC

Бренд: Allied Telesis Страницы: 3

LoadMaster 1500

Бренд: KEMP Technologies Страницы: 71

PG-FLEX RT FRL-752

Бренд: PairGain Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды