ADTRAN 1200410L2 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 80

background image

Chapter 5. Configuration Menu

48

ESU LT User Manual

61200410L2-1A

the semicolon.
Choices: 20 digits (0-9, :, and ;)

Management

Selects the management channel. Units with firmware revision D or
greater can choose either a 64 kbps TS0 management channel or the
existing 8 kbps inband channel. This would be used for remote
management applications, such as using T-Watch PRO to send and
receive configuration across an E1 span to a remote unit. For units
with firmware less than revision D, the inband channel can be
turned on or off from the

PORT

CONFIGURATION

menu.

None

Indicates that neither the inband channel nor the TS0 management
channel is utilized.

Inband

Selects the 8K inband channel as the management channel. When
this option is selected, the first time slot occupied operates in 56K
mode and the DTE clock rate is reduced by
8 kbps. This channel can be configured to always on (

N

ORMAL

), or

active only when traffic is present (

A

UTO

). If the channel is

configured for

A

UTO

and no T-Watch PRO activity is detected for

10 minutes, the inband channel is deactivated. This option is
selected in the

PORT

CONFIGURATION

menu.

The 8 kbps channel is only taken out of the first time slot. If two
64K TS0s are mapped, the DTE rate would be 120 kbps instead of
128 kbps.

The inband channel is not available in unframed mode.

The typed digits are accepted only after pressing

Enter

.

«
...
46
47
48
49
50
...
»

Содержание 1200410L2

















































































Отзывы:

Нет отзывов

Похожие инструкции для 1200410L2

Бренд: EAW Страницы: 10

Бренд: D-Link Страницы: 12

Бренд: Paradyne Страницы: 16

Бренд: Wattle Страницы: 6

Бренд: Baicells Страницы: 8

Бренд: NAIM Страницы: 2

Бренд: E-Lins Страницы: 59

Бренд: E-Lins Страницы: 11

Бренд: E-Lins Страницы: 9

Бренд: E-Lins Страницы: 5

Network Video Recorders

Бренд: e-Line Technology Страницы: 34

Бренд: Laird Страницы: 36

Бренд: DCE Страницы: 5

Бренд: Konica Minolta Страницы: 38

Бренд: Western Digital Страницы: 8

SteelCentral NetExpress

Бренд: Riverbed Страницы: 38

JetNet 3508-LVDC

Бренд: Korenix Страницы: 16

Бренд: Lanner Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды