ADTRAN 1200410L2 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 80

background image

Chapter 4. Status Menu

38

ESU LT User Manual

61200410L2-1A

LOSS OF FRAME

NI unable to frame align with incoming FAS/NFAS framing pattern.
Remote Alarm (Bit 3 of NFAS word) is transmitted out the network
interface.

LOSS OF TS16 MF

NI unable to sync on TS16 multiframe signal. Valid only when CAS/
TS16 framing enabled. Remote Multiframe Alarm is transmitted out
the network interface.

LOSS OF CRC-4

NI unable to sync on CRC-4 multiframe signal. Valid only when CRC-
4 framing is enabled. Remote Alarm is transmitted out the network
interface.

AIS RECEIVED

Unframed ones being received at network interface.

TS16 AIS RCVD

Unframed ones being received in TS16 on network interface. Remote
Multiframe Alarm transmitted out network interface.

REMOTE ALARM

Remote alarm signal (Bit 3 of NFAS word) being received at
network interface.

REMOTE MF ALARM

Remote multiframe alarm signal (Bit 6 of TS16 for three consecutive
multiframes) being received at network interface.

EXT CLOCK ALARM

No external clock at DTE.

BPV/CV RCVD

Indicates that a bipolar violation has occurred when set for AMI
line coding. Indicates that a code violation has occurred when set
for HDB3 line coding.

FAS WORD ERROR

Indicates word errors have occurred in the Frame Alignment
Signal.

E-BIT ERROR

Indicates that a Far End Block Error (FEBE) has occurred. This is
reported by the first bit of frames 13 and 15 on E1 lines that are
configured for CAS with CRC-4.

«
...
36
37
38
39
40
...
»

Содержание 1200410L2

















































































Отзывы:

Нет отзывов

Похожие инструкции для 1200410L2

DR-4100P Series

Бренд: Idis Страницы: 30

3C13886 - Router OC-3 ATM SML Flexible Interface...

Бренд: 3Com Страницы: 171

OfficeConnect WX2200

Бренд: 3Com Страницы: 204

Бренд: Lanner Страницы: 2

Бренд: LogLogic Страницы: 30

Бренд: Mercusys Страницы: 35

Бренд: JETWAY Страницы: 55

Бренд: Tbus Страницы: 25

Бренд: Faderfox Страницы: 10

Бренд: 8level Страницы: 52

OP-8000-EDFA-1U Series

Бренд: Optostar Страницы: 9

EZ-Extender Analog 120-Pin Probing Board

Бренд: Analog Devices Страницы: 29

Seven Solutions WR-ZEN Series

Бренд: Orolia Страницы: 167

Бренд: CyberTAN Страницы: 67

Бренд: Crystal Vision Страницы: 54

Бренд: Multitech Страницы: 81

iCE40 SPRAM Series

Бренд: Lattice Semiconductor Страницы: 12

Бренд: Intel Страницы: 958

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды