ADTRAN 1200410L2 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 80

background image

Chapter 2. Installation

22

ESU LT User Manual

61200410L2-1A

POWER CONNECTION

Power is supplied to the ESU LT through an IEC-type power
connector on the rear of the unit.

Grounding Instructions

Grounding instruction information from the

Underwriters'

Laboratory UL 1950 3rd Edition

is provided in this section. An

equipment grounding conductor that is not smaller in size than the
ungrounded branch-circuit supply conductors is to be installed as
part of the circuit that supplies the product or system. Bare,
covered, or insulated grounding conductors are acceptable.
Individually covered or insulated equipment grounding conductors
shall have a continuous outer finish that is either green, or green
with one or more yellow stripes. The equipment grounding
conductor is to be connected to ground at the service equipment.

The attachment-plug receptacles in the vicinity of the product or
system are all to be of a grounding type, and the equipment
grounding conductors serving these receptacles are to be connected
to earth ground at the service equipment. A supplementary
equipment grounding conductor shall be installed between the
product or system and ground that is in addition to the equipment
grounding conductor in the power supply cord.

The supplementary equipment grounding conductor shall not be
smaller in size than the ungrounded branch-circuit supply
conductors. The supplementary equipment grounding conductor
shall be connected to the product at the terminal provided, and shall
be connected to ground in a manner that will retain the ground
connection when the product is unplugged from the receptacle. The
connection to ground of the supplementary equipment grounding
conductor shall be in compliance with the rules for terminating
bonding jumpers at Part K or Article 250 of the National Electrical
Code, ANSI/NFPA 70. Termination of the supplementary

Power to the ESU LT must be from a grounded 90-240 VAC, 50/60 Hz
power source.

«
...
20
21
22
23
24
...
»

Содержание 1200410L2

















































































Отзывы:

Нет отзывов

Похожие инструкции для 1200410L2

Бренд: IEI Technology Страницы: 19

Бренд: IEI Technology Страницы: 87

Бренд: IEI Technology Страницы: 3

Бренд: Raritan Страницы: 4

Бренд: IBM Страницы: 63

Бренд: WaiLan Страницы: 27

PowerBeam AC Gen2

Бренд: Ubiquiti Страницы: 22

Бренд: Patton electronics Страницы: 12

Бренд: Renesas Страницы: 941

Optane Persistent Memory 200 Series

Бренд: Supermicro Страницы: 54

Бренд: Renesas Страницы: 4

Бренд: Leviton Страницы: 4

PSoC 4 S Series

Бренд: Cypress Страницы: 4

Бренд: ETAS Страницы: 84

Бренд: Alcatel-Lucent Страницы: 154

SteelCentral NetExpress 470

Бренд: Riverbed Страницы: 140

Smartio CP-104UL

Бренд: Moxa Technologies Страницы: 2

Бренд: Adaptec Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды