ADT Enterpreneur 3000EN Скачать руководство пользователя страница 35

Страница: 35 / 104

4-1

S E C T I O N 4

Data Field Programming

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

About Data Field Programming

The following pages list this control’s data fields in numerical order. Field numbers are listed in the
left column followed by a “Title and Data Entries” column, which lists the valid entries for each field.
Experienced installers can simply follow this column when programming the data fields. The
“Explanation” column provides explanatory information and special notes where applicable.

Use the blank programming form to record the data for this installation.

Programming Data Fields

Data field programming involves making the appropriate entries for each of the data fields.
Start Data Field programming by entering the installer code + 8 + 0 + 0.

System Setup Fields (

∗∗∗∗

20 –

∗∗∗∗

29)

FIELD

TITLE and DATA ENTRIES

EXPLANATION

*20

Installer Code

Enter 4 digits, 0000-9999

The Installer Code is used to enter programming mode and to
assign the 4-digit Master Security Code (see "Master Code" in
the

System Operation

section

for procedure). For security

purposes, the factory default installer code should be changed.

*21

Quick Arm Enable

0 = do not allow quick arm
1 = allow quick arm

If enabled, a user code is not needed to arm the system.
Instead, users can press the [#] followed by an arming key to
arm the system.
However, a user code is always needed to disarm the system.

*22

RF Jam Option

0 = no RF jam detection
1 = send RF jam report

If enabled, a report is sent if the system detects an RF
jamming signal.
UL installations must be 1 if wireless devices are used.

*23

Quick (Forced) Bypass

0 = no quick (forced) bypass
1 = allow quick bypass (code + [6] + [#])

All zones bypassed by this function will be displayed after the
bypass is initiated.
UL installations must be 0 (no forced bypass)

*24

RF House ID Code

00 = disable all wireless touchpad
usage
01–31 = House ID for partition 1, 2 and
common

The House ID identifies receivers and wireless touchpads. If a
5827 or 5827BD Wireless Touchpad or 5804BD Transmitter is
being used, a House ID code must be entered, and the
touchpad should be set to the same House ID. You can assign
RF house ID for each partition.

*26

Chime By Zone/KP Sound Enables

Entry 1

0 = no Entry 1 touchpad trouble sounds AND

no chime by zone (touchpad chimes on
fault of any entry/exit or perimeter zone
when chime mode is on)

1 = Chime by Zone enabled (select zones

to chime on zone list 3, using *81 Menu
mode)

2 = Communication Device (LRR) Trouble

sounding enabled (for communication
devices such as GSMV-ADT)

4 = System Low Battery sounding enabled
7 = select all entry 1 options

Entry 2

0 =  no Entry 2 touchpad trouble sounds
1 =  RF Supervision sounding enabled
2 =  RF Low Battery sounding enabled
4 =  RF Jam sounding enabled
7 =  select all entry 2 options

If enabled, you can define the specific zones intended to chime
when faulted while the system is in Chime mode. Use zone
list 3 to assign these zones (see

∗

81 Zone List Programming

section for details).

Keypad trouble sounding can be enabled/disabled for the

conditions listed for each entry below.

For each entry, enter the sum of the desired options.
Example Entry 1: for Chime by Zone and System Low
Battery sounding, enter 5. To enable all options, enter 7.