manualshive.com logo in svg

Adaptec ASR-2000S, Руководство по установке

Поделиться
Скачать
Adaptec ASR-2000S Скачать руководство пользователя страница 70

4-3

Installing Storage Management Software

Installation Prerequisites

The prerequisites for installing Storage Manager Pro are that you 
have already installed the following:

■

Adaptec RAID controller and drives. Refer to 

Chapter 2, 

Installing Your Controller

.

■

Controller driver. Refer to 

Chapter 3, Installing the Driver

.

Storage Manager Pro requires approximately 60 MB of free disk 
space during the installation process. After the installation is 
complete the application uses approximately 20 MB of disk space.

Note: 

If you already have Storage Manager Pro installed on 

your computer, you must uninstall it before reinstalling it. 
To uninstall Storage Manager Pro, refer to the Adaptec 
Storage Manager Pro User’s Guide.

Windows

When you install Storage Manager Pro for Windows, you 
automatically install Java Runtime Environment (JRE) 1.1.8, which is 
required to run Storage Manager Pro. This does not conflict with any 
other version of the JRE or Java Development Kit (JDK) you have 
installed.

Note: 

Do not install Storage Manager Pro on a network drive, 

because Storage Manager Pro runs as a Windows NT/2000 
service and services do not have network access rights.

To install Storage Manager Pro on Windows

1

If you are using a Windows 2000 or Windows NT system, 
verify that you have administrator privileges.

2

If your Windows system is configured to automatically start 
CD software, insert the Adaptec RAID Installation CD into your 
drive and when the installation menu appears click Install 
Adaptec Storage Manager Pro

.

Combined RAID IG.book  Page 3  Thursday, May 3, 2001  11:51 PM

Содержание ASR-2000S





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды