manualshive.com logo in svg

Adaptec ASR-2000S, Руководство по установке

Поделиться
Скачать
Adaptec ASR-2000S Скачать руководство пользователя страница 11

1-3

Introduction

Motherboard Compatibility

The Adaptec controller requires a motherboard BIOS that 

■

Complies with the PCI Local Bus Specification (revisions 2.1 and 2.2).

■

Supports multifunction devices where one of the devices is a 
PCI bridge.

■

Provides large memory-mapped address ranges.

Most motherboards manufactured since 1997 have these 
capabilities. Refer to the 

READ.ME

 file on the Adaptec RAID 

Installation CD for information about motherboard compatibility 
and a list of motherboards that Adaptec has tested with the Adaptec 
RAID controller.

Kit Contents

Your Adaptec controller kit includes the following:

■

Adaptec controller card and cables, one of the following:

■

Adaptec ATA RAID 2400A controller with four internal 
ATA/100 cables

■

Adaptec SCSI RAID 2100S, 3200S, 3210S, 3400S, or 3410S 
controller with 1 internal LVD SCSI cable with active 
terminator

■

Registration and warranty cards

■

Adaptec RAID Installation Guide (this book)

■

Adaptec RAID Installation CD, a bootable CD that includes 
RAID management software, drivers, and documentation

Combined RAID IG.book  Page 3  Thursday, May 3, 2001  11:51 PM

Содержание ASR-2000S





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды