manualshive.com logo in svg

Adaptec ASR-2000S, Руководство по установке

Поделиться
Скачать
Adaptec ASR-2000S Скачать руководство пользователя страница 12

1-4

Adaptec RAID Installation Guide

Adaptec RAID Controller Features

Adaptec RAID controllers support

■

RAID levels 0, 1, 5, multilevel 0/1 and 0/5. 

■

Cache memory modules with ECC and predictive caching.

■

PCI Local Bus Specification, Revision 2.2 with PCI clock speeds 
up to 66 MHz.

■

Microsoft Windows 2000, Windows NT, Windows 95/98/Me, 
Novell NetWare, SCO UNIX, Red Hat Linux, SuSE Linux, and 
FreeBSD.

■

OS-independent configuration and RAID creation using 
SMOR.

■

Local and remote configuration, array status, and I/O 
monitoring using Adaptec Storage Manager Pro or Storage 
Manager software.

■

Intelligent hot spares that automatically replace failed drives. 
When multiple hot spares are available on a controller, the 
intelligent hot spare algorithm picks the best spare based on 
capacity and bus location. RAIDs are rebuilt automatically 
using the new drive.

■

ASPI protocol support for third-party applications and utilities.

■

Flash ROM for easy upgrades of controller firmware, controller 
BIOS, and SMOR.

■

Event logging and broadcasting, including messaging for 
alphanumeric pagers. 

■

Windows 2000 and Windows NT only—Array expansion and 
extension during normal operation on RAID 0 or RAID 5 
arrays with the NTFS file system. Refer to the Adaptec Storage 
Manager Pro Software User’s Guide or the Adaptec Storage 
Management Software User’s Guide for specific information.

Combined RAID IG.book  Page 4  Thursday, May 3, 2001  11:51 PM

Содержание ASR-2000S





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды