manualshive.com logo in svg

Adaptec ASR-2000S, Руководство по установке

Поделиться
Скачать
Adaptec ASR-2000S Скачать руководство пользователя страница 46

3-11

Installing the Driver

Windows 95, Windows 98, and Windows Me

The following installation scenarios are discussed:

■

Installing the Driver in a New Windows 98/Me System on 
page 3-12

■

Installing the Driver in a New System with Windows 95 (OEM SR2 
– Version 95B) on page 3-14

■

Adding the Controller to an Existing Windows 95/98/Me System on 
page 3-16

■

Upgrading Windows 95 to Windows 98/Me (Upgrade Version) on 
page 3-18

Creating the Driver Disk

Each of the procedures for installing the driver in each case requires 
a slightly different procedure. However, all the procedures require 
you to create a driver disk. To create the driver disk

1

Insert the Adaptec RAID Installation CD in your drive.

2

Boot from the CD. The CD loads a Linux kernel that is used to 
manage all of its functions.

3

Follow instructions and respond to prompts as necessary to get 
to the Adaptec splash screen.

4

When you see the Adaptec splash screen, click Create Driver 
Disk

. Then, click the appropriate operating system.

5

Insert a floppy disk and click OK. The system creates the 
driver disk.

6

Shut down the system, and remove the Adaptec RAID 
Installation CD and the driver floppy disk.

Combined RAID IG.book  Page 11  Thursday, May 3, 2001  11:51 PM

Содержание ASR-2000S





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды