background image

Operator’s Guide for Rugged-UPS

TM 

1252 Series 

 

91-0120 Rev. B                                                     24 

  © Acumentrics Corporation 2007-2008 

PIN 

SIGNAL 

DEFINITION 

Low Battery Warning 

Goes True if the battery voltage indicates less than 10% hold-up time 
remaining. 

Not Utilized 

 

AC Power Good 

Goes True if AC power is viable. 

UPS Shutdown 

External Shutdown input; when True shuts down UPS. 

Signal Ground 

Common return for all other signals. 

Not Utilized 

 

UPS Power ON 

External power on input when true turns on UPS. 

Source Fail 

Goes True if the Input Power Source (AC or DC) fails or goes outside 
acceptable limits and the UPS is operating on its internal batteries. 

Overtemp Warning 

Goes True if the internal temperature of the UPS exceeds a safe upper 
limit. 

 

Smart Mode 

 

Below is a list of the commands, their function, and the format the response will be returned. Please note 
that the commands are case sensitive. The first command you must enter to start is “G”, this puts the unit 
into smart mode. You will also need the following information: 
Baud rate 2400 
Data bits 8 
Stop bits 1 
No parity 
xon/xoff 
The transmit pin is pin #8 the receive pin is pin #2 and pin#5 is the ground reference. 
 

 ??.?? *Battery voltage in volts 

 OK Chirp beeper 

 (C) ACC Copyright message (and first character sent to get into programming mode) 

???.? 

Line voltage in volts 

???.? Output voltage in volts 

???.? Power in percent full load 

R  

BYE Reset the UPS to simple signaling mode 

V  

???.? VA in percent full load 

8  

?? Error register 

01 low battery 
02 power overload 
03 Turn off from low bus voltage 
04 
05 VA overload 

9  

?? FF means AC line good, 00 means AC line bad 

p  

???.? Last power recorded when went into overload) 

v  

???.? Last VA recorded when went into overload 

 

 
 

Pin Out Specifications:   

NOTE: 

Acumentrics does not warranty the ACG1252 Series devices against damages caused 
by cables manufactured by any parties other than the Acumentrics Corporation.

 

Содержание Rugged-UPS 1252 Series
































Отзывы: