ActronAir CRQ2-14AS, Руководство по установке и пусконаладке

Страница: 16 / 36

Installation & Commissioning Guide - ESP Platinum OD Split Ducted Units
Doc. Part No. 0525-053 Ver. 5 200129 Page 16 of 36
ELECTRICAL INSTALLATION
SPLIT UNIT ELECTRICAL CONNECTION
MAINS WIRING (230VAC)
(Single Phase + Neutral) 50Hz
CONTROL WIRING (230VAC)
(Single Phase + Neutral) 50Hz
4
3
2
1
POWER AND DATA CABLE TO WALL CONTROLLER
(Cat5E spec cable with RJ45 connectors and cable boots)
EXTRA LOW VOLTAGE DATA CONTROL WIRING
(2 Core Shielded Twisted Pair 7/0.30 (0.5mm
2
) Data Cable)
*
* DO NOT USE the 2 Core Orange Shielded
Data Cable (AEDC1) used on previous
ActronAir units.
MAIN SUPPLY FROM
DISTRIBUTION BOARD
SUB-MAIN
TO UNIT
OUTDOOR
UNIT
INDOOR
UNIT
WALL
CONTROLLER
INTER-CONNECTING
PCB CABLE INDOOR
TO OUTDOOR
SUB-MAINS
ISOLATOR
(Field Supplied by Installer)
SUB-MAINS
CIRCUIT BREAKER
4
POWER and DATA
CABLE
(Supplied with the unit)
3
INTER-CONNECTING
POWER CABLE
OUTDOOR - INDOOR
2
1
IMPORTANT
To minimise noise interference, Data and Power
cable clearance should be maintained as much
as possible.
connections to be as per electrical diagram provided with
the unit.
• • Confirm that the power supply available is compatible Confirm that the power supply available is compatible
with the unit nameplate ratings. The supply power must with the unit nameplate ratings. The supply power must
be within 5% of the rated voltage. be within 5% of the rated voltage.
• • Protect electrical service from over current and Protect electrical service from over current and
short circuit conditions in accordance with AS/NZS short circuit conditions in accordance with AS/NZS
3000 “Australian / New Zealand Wiring Rules”. Size 3000 “Australian / New Zealand Wiring Rules”. Size
protection devices according to the electrical data of protection devices according to the electrical data of
the unit. the unit.
• • Complete the unit power supply wiring onto the main Complete the unit power supply wiring onto the main
isolator. isolator.
• • Secure the power cords and control cables that goes Secure the power cords and control cables that goes
in/out the unit. Use the cable ties provided in the in/out the unit. Use the cable ties provided in the
control box. control box.
• • Provide proper unit grounding in accordance with local Provide proper unit grounding in accordance with local
and national codes. and national codes.
Maximum Cable Lengths Maximum Cable Lengths
Refer to Indoor Unit’s Installation and Commissioning Refer to Indoor Unit’s Installation and Commissioning
Guide for control cable’s specifications and max. cable Guide for control cable’s specifications and max. cable
lengths. lengths.
Wiring Diagram Wiring Diagram
The wiring diagram specific for your air conditioning The wiring diagram specific for your air conditioning
system is located on the inside panel of the control system is located on the inside panel of the control
access door. Always refer all wiring installation, servicing access door. Always refer all wiring installation, servicing
and troubleshooting of this equipment to this diagram to and troubleshooting of this equipment to this diagram to
ensure correct electrical connection are satisfied. ensure correct electrical connection are satisfied.
Supply Power Requirements and Procedures Supply Power Requirements and Procedures
It is the installer’s responsibility to provide power supply It is the installer’s responsibility to provide power supply
wiring to the main isolator. wiring to the main isolator. Make sure all wirings are in
accordance with local wiring rules. Wiring should conform Wiring should conform
to all to all current electrical authority regulations and all wiring
Live Electrical Supply !
During installation of your air conditioning unit, it may be
necessary to work in close proximity to live electricity. Only
licensed electricians are allowed to perform these tasks.
Follow all electrical safety precautions when exposed to
live electrical components.
All electrical work must be carried out by a qualified and
licensed technician. Make sure all wiring is in accordance
with local wiring rules. Wiring connections should be
made in accordance with the wiring diagram provided.
DANGER