ActronAir
is constantly seeking ways to improve the design of it’s products, therefore specifications are subject to change without notice.
Copyright © 2017 Actron Engineering Pty. Ltd.
Page 9 of 36
UNIT LIFTING PROCEDURES
A. CRANE LIFTING METHOD
NOTE:
Crane lifting method is recommended for high rise lifting.
B.
FORK LIFT METHOD
PROCEDURE:
1.
To move the unit around with a forklift, insert the fork tines
through the unit feet assembly, as shown in Fig. 2.
2.
Only fork the unit through compressor end or side of the unit.
(See illustration for location of compressor end)
EQUIPMENT REQUIRED FOR CRANE LIFTING:
- 1 x shackle
- 2 x nylon slings
- spreader bar
NOTE:
Refer to catalogue for unit weight before selecting
shackles and slings.
PROCEDURE:
1. Slip nylon slings through the pallet as shown in Fig. 1.
2. Use a Bow or Dee shackle to connect the slings.
3.
Ensure slings are protected by rubber pads or similar if slings
are draped across unit edges, corners, or air grilles . This will
prevent the unit from being damaged during lifting.
4.
SPREADER BAR must be used when lifting the unit. Ensure
that the spreader bar is slightly larger than the base.
5.
Test lift the unit to determine exact unit balance and stability
before hoisting it to the installation location.
CAUTION
Length of fork lift tines must pass the unit
middle section, in order to safely carry the unit.
WH&S regulations must be observed and will
take precedence during lifting process.
WARNING
Make sure rigging equipment, accessories and plant are
sufficiently and safely capable to lift the unit in order to
prevent potential damage to property, severe personal
injury or death. Please check unit weight and weight
distribution points on unit drawing dimensions section.
DANGER
THIRD ANGLE
PROJECTION
A
Drawing Release
D
E
F
C
B
A
3
2
1
5
C
D
4
6
7
8
A
B
UNIT ASSY CRV2-14AS-0200
8011-682
7/06/2015
DL
See Notes
A3
SHEET 1 OF 1
N.T.S
DRAWING NO.
MATERIAL:
DESCRIPTION:
DATE
DRAWN BY:
APPROVED BY:
SCALE:
DRAWN DATE:
DESCRIPTION
FINISH:
REV
7/06/2015
N/A
PCR
P283
F
E
DL
ASS
EMBLY
8011-
682
BY
7.
0.1/~0
HOLE DIAMETER
1.
5 Irvine Place
written consent is prohibited
Norwest Business Park
Bella Vista NSW 2153
3.
PH. +61 2 8814 4000
A.B.N. 34 002 767 240
REV.
FOLD
3
intellectual property of Actron
This drawing always remains the
Engineering Pty Ltd. Copying,
ActronAir Pty Ltd
1
2.
FLAT PATTERN
0.5 / m
5.
4.
0.5 / m
See Notes
ANGLES & SQUARENESS
Modifying or Distributing without
GENERAL TOLERANCES
(UNLESS OTHERWISE SPECIFIED)
ALL TUBES
UNLESS OTHERWISE SPECIFIED
3rd ANGLE PROJECTION.
1.
DIMENSIONS IN MILLIMETRES.
2.
DO NOT SCALE.
3.
TUBE ENDS MUST BE ROUND AND OF FULL
4.
DIAMETER.
TUBE MUST BE CLEAN AND FREE FROM
5.
BURRS INSIDE AND OUTSIDE AND SUITABLE
OF FOR SOLDERING.
ALL BENDS 90 .
6.
ALL SHEETMETAL'S DIMENSIONS OUTISDE.
A
250
227
*
195
68
PALLET TINE LIFT OPENING DIMENSIONS
All dimensions in mm.
Detail - “
A
”
THIRD ANGLE
PROJECTION
DL
A
Drawing Release
D
E
F
C
B
A
3
2
1
5
C
D
4
6
7
8
A
B
UNIT ASSY CRV2-14AS-0200
8011-682
7/06/2015
DL
See Notes
A3
SHEET 1 OF 1
N.T.S
DRAWING NO.
MATERIAL:
DESCRIPTION:
DATE
DRAWN BY:
APPROVED BY:
SCALE:
DRAWN DATE:
DESCRIPTION
FINISH:
REV
7/06/2015
N/A
PCR
P283
F
ASS
EMBLY
8011-
682
BY
7.
3
2.
1
ActronAir Pty Ltd
This drawing always remains the
1.
5 Irvine Place
HOLE DIAMETER
3.
0.1/~0
E
FOLD
intellectual property of Actron
PH. +61 2 8814 4000
A.B.N. 34 002 767 240
Bella Vista NSW 2153
REV.
See Notes
ANGLES & SQUARENESS
Engineering Pty Ltd. Copying,
FLAT PATTERN
5.
0.5 / m
0.5 / m
Modifying or Distributing without
written consent is prohibited
4.
Norwest Business Park
GENERAL TOLERANCES
(UNLESS OTHERWISE SPECIFIED)
ALL TUBES
UNLESS OTHERWISE SPECIFIED
3rd ANGLE PROJECTION.
1.
DIMENSIONS IN MILLIMETRES.
2.
DO NOT SCALE.
3.
TUBE ENDS MUST BE ROUND AND OF FULL
4.
DIAMETER.
TUBE MUST BE CLEAN AND FREE FROM
5.
BURRS INSIDE AND OUTSIDE AND SUITABLE
OF FOR SOLDERING.
ALL BENDS 90 .
6.
ALL SHEETMETAL'S DIMENSIONS OUTISDE.
A
Slip nylon slings
through the pallet
Pallet
Unit
THIRD ANGLE
PROJECTION
DL
A
Drawing Release
D
E
F
C
B
A
3
2
1
5
C
D
4
6
7
8
A
B
UNIT ASSY CRV2-14AS-0200
8011-682
7/06/2015
DL
See Notes
A3
SHEET 1 OF 1
N.T.S
DRAWING NO.
MATERIAL:
DESCRIPTION:
DATE
DRAWN BY:
APPROVED BY:
SCALE:
DRAWN DATE:
DESCRIPTION
FINISH:
REV
7/06/2015
N/A
PCR
P283
F
ASS
EMBLY
8011-
682
BY
7.
3
2.
1
ActronAir Pty Ltd
This drawing always remains the
1.
5 Irvine Place
HOLE DIAMETER
3.
0.1/~0
E
FOLD
intellectual property of Actron
PH. +61 2 8814 4000
A.B.N. 34 002 767 240
Bella Vista NSW 2153
REV.
See Notes
ANGLES & SQUARENESS
Engineering Pty Ltd. Copying,
FLAT PATTERN
5.
0.5 / m
0.5 / m
Modifying or Distributing without
written consent is prohibited
4.
Norwest Business Park
GENERAL TOLERANCES
(UNLESS OTHERWISE SPECIFIED)
ALL TUBES
UNLESS OTHERWISE SPECIFIED
3rd ANGLE PROJECTION.
1.
DIMENSIONS IN MILLIMETRES.
2.
DO NOT SCALE.
3.
TUBE ENDS MUST BE ROUND AND OF FULL
4.
DIAMETER.
TUBE MUST BE CLEAN AND FREE FROM
5.
BURRS INSIDE AND OUTSIDE AND SUITABLE
OF FOR SOLDERING.
ALL BENDS 90 .
6.
ALL SHEETMETAL'S DIMENSIONS OUTISDE.
A
Connect the loop ends of slings unto shackle
Fig. 1
“
A
”
THIRD ANGLE
PROJECTION
A
Drawing Release
D
E
F
C
B
A
3
2
1
5
C
D
4
6
7
8
A
B
UNIT ASSY CRV2-14AS-0200
8011-682
7/06/2015
DL
See Notes
A3
SHEET 1 OF 1
N.T.S
DRAWING NO.
MATERIAL:
DESCRIPTION:
DATE
DRAWN BY:
APPROVED BY:
SCALE:
DRAWN DATE:
DESCRIPTION
FINISH:
REV
7/06/2015
N/A
PCR
P283
F
E
DL
ASS
EMBLY
8011-
682
BY
7.
0.1/~0
HOLE DIAMETER
1.
5 Irvine Place
written consent is prohibited
Norwest Business Park
Bella Vista NSW 2153
3.
PH. +61 2 8814 4000
A.B.N. 34 002 767 240
REV.
FOLD
3
intellectual property of Actron
This drawing always remains the
Engineering Pty Ltd. Copying,
ActronAir Pty Ltd
1
2.
FLAT PATTERN
0.5 / m
5.
4.
0.5 / m
See Notes
ANGLES & SQUARENESS
Modifying or Distributing without
GENERAL TOLERANCES
(UNLESS OTHERWISE SPECIFIED)
ALL TUBES
UNLESS OTHERWISE SPECIFIED
3rd ANGLE PROJECTION.
1.
DIMENSIONS IN MILLIMETRES.
2.
DO NOT SCALE.
3.
TUBE ENDS MUST BE ROUND AND OF FULL
4.
DIAMETER.
TUBE MUST BE CLEAN AND FREE FROM
5.
BURRS INSIDE AND OUTSIDE AND SUITABLE
OF FOR SOLDERING.
ALL BENDS 90 .
6.
ALL SHEETMETAL'S DIMENSIONS OUTISDE.
A
Fig. 2
INSERT FORKLIFT
TINES HERE
INSERT FORKLIFT
TINES HERE
*
COMPRESSOR
END
CAUTION
DO NOT LIFT UNIT
from this end.
227
*
195
*
250
*
* Side pallet tine openings may not be available on some models.
Содержание CRQ2-14AS
Страница 35: ...THIS PAGE IS INTENTIONALLY LEFT BLANK ...
