SERIES IP1K100 INDUSTRIAL I/O PACK RECONFIGURABLE DIGITAL I/O MODULE
___________________________________________________________________________________________
- 18 -
NineK453a.acf…….……………. Altera Maxplus II ASCII text file
that stores information about
connected pin, and device
assignments, as well as
configuration settings for the
Compiler, Simulator, and Timing
Analyzer for an entire project.
Clock Generator
Clock Generator IC…………….. Cypress ICD2053B
Frequency range 391KHz to
100MHz.
BitCalc2k1.exe………………….. C executable program which
provides the register values need
to program the clock generator
chip for your selected frequency.
This program is included in the
Engineering Design kit for the
IP1K100.
APPENDIX
CABLE: MODEL 5025-551-x (Shielded)
Type: Flat Ribbon Cable, 50-wires (female connectors at both
ends). The ‘-x’ suffix designates the length in feet (12 feet
maximum). Choose shielded cable according to model number.
The shielded cable is highly recommended for optimum
performance with analog input or output modules.
Application: Used to connect a Model 5025-552 termination panel to
the AVME9630/9660, APC8610, or APC8620/1 non-intelligent
carrier board connectors (both have 50-pin connectors).
Length: Last field of part number designates length in feet (user-
specified, 12 feet maximum). It is recommended that this length
be kept to a minimum to reduce noise and power loss.
Cable: 50-wire flat ribbon cable, 28 gage. Shielded cable model
uses Acromag Part 2002-261 (3M Type 3476/50 or equivalent).
Headers (Both Ends): 50-pin female header with strain relief.
Header - Acromag Part 1004-512 (3M Type 3425-6600 or
equivalent). Strain Relief - Acromag Part 1004-534 (3M Type
3448-3050 or equivalent).
Keying: Headers at both ends have polarizing key to prevent
improper installation.
Schematic and Physical Attributes: See Drawing 4501-463.
Shipping Weight: 1.0 pound (0.5Kg) packaged.
TERMINATION PANEL: MODEL 5025-552
Type: Termination Panel For AVME9630/9660, APC8610, or
APC8620 Boards
Application: To connect field I/O signals to the Industrial I/O
Pack (IP). Termination Panel: Acromag Part 4001-040
(Phoenix Contact Type FLKM 50). The 5025-552 termination
panel facilitates the connection of up to 50 field I/O signals and
connects to the AVME9630/9660 3U/6U, APC8610, or
APC8620/1 non-intelligent carrier boards (field connectors only)
via a flat ribbon cable (Model 5025-551-x). The A-D connectors
on the carrier board connect the field I/O signals to the P2
connector on each of the Industrial I/O Pack modules. Field
signals are accessed via screw terminal strips. The terminal
strip markings on the termination panel (1-50) correspond to P2
(pins 1-50) on the Industrial I/O Pack (IP). Each Industrial I/O
Pack (IP) has its own unique P2 pin assignments. Refer to the
IP module manual for correct wiring connections to the
termination panel.
Schematic and Physical Attributes: See Drawing 4501-464.
Field Wiring: 50-position terminal blocks with screw clamps. Wire
range 12 to 26 AWG.
Connections to AVME9630/9660, APC8610, or APC8620/1: P1,
50-pin male header with strain relief ejectors. Use Acromag
5025-551-x cable to connect panel to VME board. Keep cable
as short as possible to reduce noise and power loss.
Mounting: Termination panel is snapped on the DIN mounting rail.
Printed Circuit Board: Military grade FR-4 epoxy glass circuit board,
0.063 inches thick.
Operating Temperature: 0 to +70
°
C.
Storage Temperature: -25
°
C to +85
°
C.
Shipping Weight: 1.25 pounds (0.6kg) packaged.
TRANSITION MODULE: MODEL TRANS-GP
Type: Transition module for AVME9630/9660 boards.
Application: To repeat field I/O signals of IP modules A through D
for rear exit from VME card cages. This module is available for
use in card cages which provide rear exit for I/O connections via
transition modules (transition modules can only be used in card
cages specifically designed for them). It is a double-height
(6U), single-slot module with front panel hardware adhering to
the VMEbus mechanical dimensions, except for shorter printed
circuit board depth. Connects to Acromag termination panel
5025-552 from the rear of the card cage, and to
AVME9630/9660 boards within card cage, via flat 50-pin ribbon
cable (cable Model 5025-551-X).
Schematic and Physical Attributes: See Drawing 4501-465.
Field Wiring: 100-pin header (male) connectors (3M 3433-D303 or
equivalent) employing long ejector latches and 30 micron gold in
the mating area (per MIL-G-45204, Type II, Grade C).
Connects to Acromag termination panel 5025-552 from the rear
of the card cage via flat 50-pin ribbon cable (cable Model
5025-551-X).
Connections to AVME9630/9660: 50-pin header (male) connectors
(3M 3433-1302 or equivalent) employing long ejector latches
and 30 micron gold in the mating area (per MIL-G-45204, Type
II, Grade C). Connects to AVME9630/9660 boards within the
card cage via flat 50-pin ribbon cable (cable Model 5025-551-X).
Mounting: Transition module is inserted into a 6U-size, single-width
slot at the rear of the VMEbus card cage.
Printed Circuit Board: Six-layer, military-grade FR-4 epoxy glass
circuit board, 0.063 inches thick.
Operating Temperature: 0 to +70
°
C.
Storage Temperature: -25
°
C to +85
°
C.
Shipping Weight: 1.25 pounds (0.6Kg) packaged.
