manualshive.com logo in svg

Acorn Computers Limited BBC A, Руководство по оборудованию, Страница: 37 / 47

Поделиться
Скачать
Acorn Computers Limited BBC A Скачать руководство пользователя страница 37

37

 

3.18 The 1MHz Bus Interface. 

 

In addition to the high speed 

"Tube”

 

interface the BBC Microcomputer also has a 1MHz extension bus. 

Connection to this interface is through PL11 on the underside of the machine. The 1MHZ extension bus 

provides buffered address lines A0 to A7 (IC71), buffered bi-directional data bus lines D0 to D7 (IC72) 

and numerous control lines. The interface also has an analogue input line which is fed to the machines 

internal audio amplifier (IC's 17 and 19) and loudspeaker. The input impedance of this analogue input is 9 

kilohms. If the speech and internal sound generator systems are not in use then a signal of + 3 volts RMS 

will produce full volume output at the loudspeaker. This input level will need to be reduced in order to 

avoid excessive distortion if the speech and sound generator systems are in use at the same time. There 

are two other lines on the 1MHz bus connector which will require further explanation, these are the lines 

NPGFC (Not PaGe &FC ) and NPGFD (Not PaGe &FD) which are often referred to as FRED and JIM 

respectively. 

 

3.19 

FRED. 

 

This signal is decoded from the machines address bus such that when the address bus holds a valid 

address in the range &FC00 to &FCFF this line will go low. The microcomputer address decoding circuitry 

around IC20 (74LS139) is used to accomplish this. FRED is intended for use by peripheral devices with 

small memory requirements. 

 

There are various links within the machine that can be used to enable/disable FRED (S17) or alter its 

access times (S16) Further information on these links is given in chapter 4. 

 

Acorn Computers Ltd. have standardised on particular addresses in the range &FC00 to &FCFF (FRED) 

to be used for specific functions, at the present time these are as  

&FC00  - &FC0F 

Test hardware use. 

&FC18  - &FC13 

Teletext use. 

&FC14  - &FC1F 

Prestel use. 

&FC20  - &FC27 

IEEE 488 interface (Control Universal Ltd.). 

&FC28  - &FC2F 

Future Acorn expansion. 

&FC30  - &FC3F 

Cambridge Ring interface. 

&FC40  - &FC47 

Winchester disc interface. 

&FC48  - &FC7F 

Future Acorn expansion. 

&FC80  - &FC8F 

Test hardware devices. 

&FC90  - &FCBF 

Future Acorn expansion. 

&FCC8 - &FCFE 

User applications. 

&FCFF  

JIM paging register (see JIM) 

 

TABLE 3.2 

 

Содержание BBC A
















































Отзывы:

Нет отзывов