Acer AR360 F1 Series Скачать руководство пользователя страница 86

Страница: 86 / 188

3 System upgrades

Installing the system into the rack

Caution: To minimize the chances of injuries, make sure that two
or more people help in installing the server.

To install the system into a four-post rack

Confirm that the left and right inner rails have been correctly
identified.

Remove the inner rails from the mounting rails.

Extend the inner rail from the mounting rail until the rail release latch
clicks (1).

Press the release latch (2) and slip the inner rail out.

Do the same thing to the other mounting rail.

Caution: To avoid personal injury, care should be taken when
pressing the inner rail release latches and sliding the component
into the rack.

Содержание AR360 F1 Series




























































































































































































Результаты поиска

Содержание AR360 F1 Series

Отзывы:

Похожие инструкции для AR360 F1 Series

Бренды по названию

Популярные бренды

Acer AR360 F1 Series, Руководство пользователя

Результаты поиска

Содержание AR360 F1 Series

Отзывы:

Похожие инструкции для AR360 F1 Series

Бренды по названию

Популярные бренды